Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: make a motor coupling with ease...  (Read 2441 times)

rathikrishna

  • Guest
make a motor coupling with ease...
« on: December 29, 2011, 08:41:29 am »

Friends..one of the great worry of a boat modeller is about the coupling between motor and drive shafts..even i was in trouble to find a good easy solution for a coupling..we can buy a coupling from hobby store..is far expensive..and can make one from a lathe..but must wait for their favor..especially for a tiny minute work like this...so i found a simple effective solution..and tried this year in ship model competitions..proved very successful..we can make any coupling to any motors...with ease..in minutes...

collect some bicycle spoke nipples, in various sizes..its very inexpensive..but strong..and yes non rusty as it all are made of brass...

collect some stain less steel bicycle spokes in various sizes..also inexpensive...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #1 on: December 29, 2011, 08:43:49 am »

now i am planing to fix this EP 400 motor to a patrol boat...so drive a nipple with hammer, on to the shaft while placing the back of the shaft on a bench vise...
after making sure it is straight..apply some industrial cyano glue in to it...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #2 on: December 29, 2011, 08:45:31 am »

cut a piece of brass rod, in to appropriate length, and make sure it is tight with the driven nipple...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #3 on: December 29, 2011, 08:47:02 am »

apply cyano to it...
place a second nipple in same size to the opposite side...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #4 on: December 29, 2011, 08:48:32 am »

now wait to dry...
can see how simpleit is...
we can drive in a spoke, in to the thread of the nipple as shown..make sure thread is ok...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #5 on: December 29, 2011, 08:50:15 am »

now drill a hole on nipple as shown..a 2mm bit is good, for this tiny shaft...
take a third nipple and thread to the desired spoke as shown...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #6 on: December 29, 2011, 08:51:41 am »

start to thread in the spoke in to the motor...

and tight the counter nipple with nose pliers...drop some cyano...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #7 on: December 29, 2011, 08:52:40 am »

now its ok..
time to fix on the craft....
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #8 on: December 29, 2011, 08:54:11 am »

we can make any size of coupling from bicycle nipples..can drill a hole along, so can lock it with a tiny bolt...firm...
Logged

rathikrishna

  • Guest
Re: make a motor coupling with ease...
« Reply #9 on: December 29, 2011, 08:55:24 am »

as no ballpoint tube or silicon tubes are used..no issues with heating up.... :-)) :-)) :-))
Logged
Pages: [1]   Go Up
 

Page created in 0.653 seconds with 16 queries.