Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: SS Furie from Deans Marine  (Read 4945 times)

colin-d

  • Guest
SS Furie from Deans Marine
« on: November 18, 2009, 11:27:31 am »

the Wife took a liking to this one when we seen her mored up along side the Steam museum in Maasluiss (Holland) between Hook van Holland and Rotterdam.

heres a photo of the original
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #1 on: November 18, 2009, 11:30:37 am »

the making of the rudder;

little brass nails have been shorted to fit, and the plastic strips are from slaters.

the prop and tillerarm have been changed from what came with the kit, to a tillerarm from Robbe and a prop from Raboesch.
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #2 on: November 18, 2009, 11:35:13 am »

instead of using the wood that came with the kit (I'm not a good friend of Wood, and neither is water)    ;-)

so i have used plastic for the Deck support beams and made my own "H" beams

the propshaft is also from Raboesch, the motor is from Buehler
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #3 on: November 18, 2009, 11:37:57 am »

here's a photo of most of the Skylights, and the Engine room cover.
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #4 on: November 18, 2009, 11:42:19 am »

Building the Bridge was rather complex, and one could spend hours up on hours doing mods and alterations, or even insted of using the supplied plastic, using Wood as in the Real Furie.

i opted for the plastic, and try and make it look like wood.. !!  O0
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #5 on: November 18, 2009, 11:43:18 am »

just to follow on here the bridge
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #6 on: November 18, 2009, 11:52:02 am »

both masts were build in much the same way, instead of using the supplied wood, i decided to go for Brass, so as to hide the wires for the working lights (LED's), the front mast also doubles up as the Aerial for the Radio gear.

the dingy i thought would be nice if all the ribs were put in the vacform, so it looks a little bit more like a dingy instead of a vacform !!

Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #7 on: November 18, 2009, 11:59:27 am »

time for the painwork;

no i have not used a spray gun

all the painting was done by Hand, yes, a paint brush, well different sizes of course, and the little tins of paint from Humbrol which were thinned slightly, once all was dry, i applied a few coats of clear satin varnish to protect the paint work.
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #8 on: November 18, 2009, 12:06:39 pm »

and once all was finished it was time for the maiden voyage.

since Building this model, i have entered a few steering competitions on the continent (Germany, my home from home), and low and behold have managed to come in under the top 4 a few times.

hope you all enjoy the photo's, i enjoyed builder Her.
Logged

polobeer

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 350
  • Location: SE France
Re: SS Furie from Deans Marine
« Reply #9 on: November 18, 2009, 12:26:30 pm »

What a lovely model Colin! A very cleanly built example of this nice looking tug.

All the best
Simon  %%
Logged

shıp110

  • Guest
Re: SS Furie from Deans Marine
« Reply #10 on: November 18, 2009, 08:40:35 pm »

of tugboat model and all I love. Fine details. very beautiful model. :-))
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #11 on: November 19, 2009, 12:51:21 pm »

thanks for your comments, and glad you enjoyed to photo's
Logged

tugmad

  • Guest
Re: SS Furie from Deans Marine
« Reply #12 on: November 19, 2009, 01:56:44 pm »

A LOVELY MODEL BUT A SHAME ON YOU PUTTING A 5 BLADED PROPELLOR ON A STEAM TUG, THE CHIEF ENGINEER WOULD BE PULLING HIS HAIR OUT WITH ENGINE ALWAYS STOPPING AT TDC    {-) {-) {-) {-)
Logged

colin-d

  • Guest
Re: SS Furie from Deans Marine
« Reply #13 on: November 19, 2009, 02:02:37 pm »

jup i know :embarrassed:, it was the only Prop i had at the time with the right diameter, since the model has been finished and been on the water a few times, i now have a 3 Bladed Brass Prop on the model. :-))

with the 5 Bladed prop it went like Sh** of a shovel..   {-)
Logged
Pages: [1]   Go Up
 

Page created in 0.093 seconds with 22 queries.