Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Springer Crane  (Read 6405 times)

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Springer Crane
« on: August 13, 2013, 11:00:44 am »

I was given a springer hull with crane superstructure on the weekend, no running gear but I have a Graupner 900 that I am going to fit into it - The crane may have to go as I am told it pulls the boat over when turned to the side (crane turns through 360 degrees and hook winds in and out, extension and lift has to be done by hand) -

Wayne



Logged

Circlip

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 4,449
  • Location: North of Watford, South of Hadrians wall
Re: Springer Crane
« Reply #1 on: August 13, 2013, 11:18:40 am »

If you wanted to retain the crane (?) what about adding flat plate "Wings" to either side of the hull? Same width as retracted crane jib, below surface and painted a dark colour to "Hide" them?
 
  Regards   Ian.
Logged
You might not like what I say, but that doesn't mean I'm wrong.
 
What I said is not what you  think you heard.

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #2 on: August 13, 2013, 11:22:43 am »

Hi Ian, not sure that would work, even retracted the jib extends about 25cm out from the side of the hull. I had thought about a long keel like yachts have? Or adding a bit of weight to the crane at the back of the jib, where the real crane would have concrete weights, might help a bit

Wayne
Logged

Circlip

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 4,449
  • Location: North of Watford, South of Hadrians wall
Re: Springer Crane
« Reply #3 on: August 13, 2013, 11:42:10 am »

Worth trying with a flat plate and a rubber band before any "Commitment" to glue etc.
 
    Regards  Ian
Logged
You might not like what I say, but that doesn't mean I'm wrong.
 
What I said is not what you  think you heard.

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #4 on: August 13, 2013, 11:58:23 am »

ah good idea, I have some 2mm plastic card somewhere that should do. Need to buy a replacement motor for the crane windlass first as the old one has given up the ghost and I am waiting for a 360 degree servo too. Plenty of time anyway to sand down the hull and repaint it.

Wayne
Logged

Martin (Admin)

  • Administrator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 23,359
  • Location: Peterborough, UK
    • Model Boat Mayhem
Re: Springer Crane
« Reply #5 on: August 13, 2013, 12:48:20 pm »


You could also just extend the jib up and over the front..... even then I think it pitch over.....  {:-{
Logged
"This is my firm opinion, but what do I know?!" -  Visit the Mayhem FaceBook Groups!  &  Giant Models

Arrow5

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,873
  • Location: Scottish Highlands
Re: Springer Crane
« Reply #6 on: August 13, 2013, 12:51:14 pm »

Finish the Springer and make crane-barge to tow, the barge can be any shape or size to suit. A bit more weight reduction by removing the truck cab at the front.
Logged
..well can you land on this?

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #7 on: August 13, 2013, 01:29:20 pm »

Thanks arrow5, that is something to think about, though I am sure the barge willstill tip over, unless I make it none working of course.
Logged

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #8 on: August 13, 2013, 01:30:10 pm »


You could also just extend the jib up and over the front..... even then I think it pitch over.....  {:-{


I think the motor and battery weight might stop it from pitching over - Will see once I get going with the rebuild

Wayne
Logged

Circlip

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 4,449
  • Location: North of Watford, South of Hadrians wall
Re: Springer Crane
« Reply #9 on: August 13, 2013, 01:34:52 pm »

Quote
though I am sure the barge will still tip over,

  Not if the barge is 5 times wider than the tug. {-)        Problem with adding a weighted keel or bunging weight onto the back of the crane is the lowering (or increasing) the loading of the hull.   ie. the waterline is getting closer to the deck.
 
   Regards  Ian.
Logged
You might not like what I say, but that doesn't mean I'm wrong.
 
What I said is not what you  think you heard.

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #10 on: August 13, 2013, 01:48:40 pm »

Problem with adding a weighted keel or bunging weight onto the back of the crane is the lowering (or increasing) the loading of the hull.   ie. the waterline is getting closer to the deck.

Thanks, something to remember - Re the barge, of course it can be much wider than the tug, actually I am warming to the idea of a barge now!
Logged

Umi_Ryuzuki

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,395
  • Location: PDX, OR USA
    • Models and Miniatures
Re: Springer Crane
« Reply #11 on: August 13, 2013, 06:08:41 pm »

I second the crane barge idea.

 :-)) :-))

Springer tug sheerleg crane barge

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #12 on: August 20, 2013, 09:34:32 pm »

Thanks Umi, nice pics. I have decided to rebuilt the springer as a tug and I will then sort out a barge for the crane at a later stage - Drawing out a superstructure design this week.

Wayne
Logged

warspite

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,757
Re: Springer Crane
« Reply #13 on: August 21, 2013, 08:12:05 am »

Have you ever seen one of these cranes working, they have outriggers that the driver extends to lift the vehicle of the ground and give better stability  ok2
Sooooo - what about outrigging floatation devices that are extended to increase the stability ;)
(though not sure how big to make them)
Logged
Operational - 1/72 LCMIII, 1/180 Sovereign, HMS Victory to be sailed
Non Operational - 1/72 Corvette, 1/72 E-Boat, 1/72 vosper mtb
incomplete, tug, cardboard castle class convert

derekwarner

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 9,463
  • Location: Wollongong Australia
Re: Springer Crane
« Reply #14 on: August 21, 2013, 08:27:05 am »

Hey warspite......I understand what you mean....however in todays world  :o ...computerised ballasting in floating crane lifting vessels replaces the need for   .....
"outriggers that the driver extends to lift the vehicle of the ground and give better stability"  :-))
 
Derek
Logged
Derek Warner

Honorary Secretary [Retired]
Illawarra Live Steamers Co-op
Australia
www.ils.org.au

warspite

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,757
Re: Springer Crane
« Reply #15 on: August 21, 2013, 08:37:02 am »

I was thinking more for comical effect, being a springer  O0 , if it works then it looks like a good feature, was thinking of those rubber tanks that they uses to keep ships spaced of the jetties  :-)) , a couple of the lids from Lynx cans, the domed type if you know what I mean.
Logged
Operational - 1/72 LCMIII, 1/180 Sovereign, HMS Victory to be sailed
Non Operational - 1/72 Corvette, 1/72 E-Boat, 1/72 vosper mtb
incomplete, tug, cardboard castle class convert

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #16 on: August 21, 2013, 11:28:01 am »

Mmm thanks warspite, also not a bad idea, can be looked at as a second superstructure for the springer

Wayne
Logged

goBulawayo

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 368
  • Location: West Wales
Re: Springer Crane
« Reply #17 on: September 22, 2013, 07:33:45 pm »

Hi All, some pics and a bit of video of my springer with the start of a new superstructure out sailing today

Wayne.




http://s297.photobucket.com/user/gubulawayo/media/DSCF3403.mp4.html
the motor noise in the video is not from the tug
Logged

warspite

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,757
Re: Springer Crane
« Reply #18 on: September 22, 2013, 11:13:36 pm »

just watch out for jaws trying to munch through those floats on the chopper  :P , now where did i put my coat  {:-{
Logged
Operational - 1/72 LCMIII, 1/180 Sovereign, HMS Victory to be sailed
Non Operational - 1/72 Corvette, 1/72 E-Boat, 1/72 vosper mtb
incomplete, tug, cardboard castle class convert
Pages: [1]   Go Up
 

Page created in 0.107 seconds with 22 queries.