Model Boat Mayhem - Forum

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Ann letitia russel  (Read 465 times)

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,248
  • member of the Potteries Model boat club
Ann letitia russel
« on: September 13, 2018, 05:23:57 PM »

anchor . What attaches to the anchor, rope or chain, then rope,where is the anchor rope/ chain stored?
Also what type of cleats do the rudder lift and lower ropes attach to.
Thanks for looking guys.




John,




Logged

Neil

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,219
  • Location: near Fleetwood
Re: Ann letitia russel
« Reply #1 on: September 13, 2018, 10:06:28 PM »


these ones for the cleats,  john but to be honest I don't think they were stored on dek…..there were roap bins in the aft and fore cockpits...BUT.……...the way I had to design the kits so that the cockpits lifted out, I couldn't put them in to the boat, as the rope bins were under the decks on the side of the hull.


when I later designed the Watson 46' and the Barnett 51' boats I made the cockpits permanent with lift out floors so that the side storage under decks was a part pf the design, and the rope storage bins went in.
Logged

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,248
  • member of the Potteries Model boat club
Re: Ann letitia russel
« Reply #2 on: September 14, 2018, 09:33:31 AM »

Thanks for the info Neil, I am finishing off the rigging today then she will be finished.
I will send you a photo.


Cheers mate,


John
Logged

Neil

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,219
  • Location: near Fleetwood
Re: Ann letitia russel
« Reply #3 on: September 14, 2018, 10:09:48 PM »

Thanks for the info Niel, I am finishing off the rigging today then she will be finished.
I will send you a photo.
Cheers mate,
John



look forward to seeing it...…….looks like my two Watson's are finding a new home after all these years...……….I'll be sad to see them go, but they'll be looked after by the new owner.
Logged

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,248
  • member of the Potteries Model boat club
Re: Ann letitia russel
« Reply #4 on: September 15, 2018, 06:32:04 PM »

Hi Neil, did you get the e.mail picture I sent, I don't know how to post to the forum using my
I- pad so you could see the picture here.
Could you or anyone tell me how many ceramic insulators there were on the radio aerial wires
Please.


John
Logged

Neil

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,219
  • Location: near Fleetwood
Re: Ann letitia russel
« Reply #5 on: September 15, 2018, 09:25:30 PM »

Hi Neil, did you get the e.mail picture I sent, I don't know how to post to the forum using my
I- pad so you could see the picture here.
Could you or anyone tell me how many ceramic insulators there were on the radio aerial wires
Please.
John

Here it is john. and it is an absolute cracker...……..I feel very proud when someone sends me a picture of their ALR model and you should certainly be proud of that...…...stunning. well done..as for insulators, bearing in mind that I took my information for mine from an old faded photo in a book, there were two each wire on each end of the two lines from fore to aft mast and each was about 25mm apart and 25mm from the mast connection...… but that was a "misty" photo.

Logged

Neil

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,219
  • Location: near Fleetwood
Re: Ann letitia russel
« Reply #6 on: September 15, 2018, 09:30:14 PM »


tried inverting on my file and it still comes in upside down whether inverted OR right way up in my file.
 >>:-( {:-{ <:(
Logged

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,248
  • member of the Potteries Model boat club
Re: Ann letitia russel
« Reply #7 on: September 15, 2018, 10:07:42 PM »

Thanks for that Neil, she is indeed a beautiful looking boat a credit to you for designing it
For kit form.


John
Logged

Martin [Admin]

  • Administrator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 17,916
  • Location: Peterborough, UK
    • Model Boat Mayhem
Re: Ann letitia russel
« Reply #8 on: September 15, 2018, 11:09:13 PM »

tried inverting on my file and it still comes in upside down whether inverted OR right way up in my file.
 >>:-( {:-{ <:(

Fixed!   :-)
Logged
"This is my firm opinion, but what do I know?!"    -   Mayhem FaceBook Group!

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,248
  • member of the Potteries Model boat club
Re: Ann letitia russel
« Reply #9 on: September 15, 2018, 11:44:21 PM »

Thank you Martin :-))


John
Logged

Neil

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,219
  • Location: near Fleetwood
Re: Ann letitia russel
« Reply #10 on: September 16, 2018, 12:11:56 AM »

Logged
Pages: [1]   Go Up