Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: boat id please  (Read 4108 times)

gwa84

  • Guest
boat id please
« on: December 08, 2011, 06:23:14 pm »
Logged

Patrick Henry

  • Guest
Re: boat id please
« Reply #1 on: December 08, 2011, 06:26:16 pm »
A Pipedream maybe?
Logged

cobramax

  • Guest
Re: boat id please
« Reply #2 on: December 08, 2011, 06:27:23 pm »
Looks like a Bernard Holder "Crusader"   99.999%
Logged

andyn

  • Guest
Re: boat id please
« Reply #3 on: December 08, 2011, 06:32:49 pm »
Crusader 2
Logged

gwa84

  • Guest
Re: boat id please
« Reply #4 on: December 08, 2011, 07:19:14 pm »
i was thinking crusader dident know ther was a 2 i have the 36 inch version just looked difent to that cheers peeps

is he still making boats ?
Logged

andyn

  • Guest
Re: boat id please
« Reply #5 on: December 08, 2011, 07:31:03 pm »
The little 36 inch one is the Crusader 3

I don't know if he's still going, he was ill recently. I believe he is, but can't confirm it...
Logged

gwa84

  • Guest
Re: boat id please
« Reply #6 on: December 08, 2011, 07:37:25 pm »
andy do you recon a sc61 with tuned pipe will run it ok keeping the conventional drive  :-))
Logged

andyn

  • Guest
Re: boat id please
« Reply #7 on: December 08, 2011, 10:48:07 pm »
Yup, perfect :-))
Logged

gwa84

  • Guest
Re: boat id please
« Reply #8 on: December 14, 2011, 01:46:59 am »
got the boat  :-)) its in worse state then it looks in the pick but for 30 quid worth the mony  has enybody got a coppy of the origanal set up instructions that came with it from bernard as the prop and rudder look well out of place and are seazed solid so will need replacing enyway  :-))
Logged

andyn

  • Guest
Re: boat id please
« Reply #9 on: December 14, 2011, 11:00:07 am »
The rudder if I remember rightly should be an inch and a half infront of the transom, then there should be another inch and a half between Rudder and prop, but far as I can tell from those pics they look about right

Andy :-)
Logged

gwa84

  • Guest
Re: boat id please
« Reply #10 on: December 14, 2011, 04:46:54 pm »
col thanks andy  :-))   ive just got hold of a sub serfice flexy drive so i can have the angle a lot shalower then with a streat shaft  :-))
Logged

triumphjon

  • Guest
Re: boat id please
« Reply #11 on: December 14, 2011, 06:39:27 pm »
as bernard is a member of the bristol pegasus model boat club , if you can make contact with them im sure somebody could put you in contact with him !
Logged

omra85

  • Guest
Re: boat id please
« Reply #12 on: December 15, 2011, 09:08:04 am »
Hi Geoff
Bernard is still making boats and fittings on a limited basis (due to his health) but I'm sure would be happy to chat about the best way to get the boat back on the water. His number is 01454 417803.
The boat looks like it came from Stevenage (SV on the transom) and was probably over powered by a CMB 45.

Cheers
Danny
Logged

andyn

  • Guest
Re: boat id please
« Reply #13 on: December 15, 2011, 02:34:23 pm »
Probably did come from Stevenage, but not anytime within the last 5 years as I've never seen it before...
Logged

triumphjon

  • Guest
Re: boat id please
« Reply #14 on: December 15, 2011, 03:12:25 pm »
thank you danny , ive lost all of my own contact details over the last few years , although i used to be a pegasus member ( PG 3 )
Logged

gwa84

  • Guest
Re: boat id please
« Reply #15 on: December 15, 2011, 05:46:51 pm »
by the look of all the fitings and propshaft the amount of rust sugests its been eather underwater or outside for quite some time
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.029 seconds with 16 queries.