Model Boat Mayhem
Technical, Techniques, Hints, and Tips => Tutorials & "How To’s" ... => Topic started by: Martin13 on November 17, 2007, 09:23:45 pm
-
I am building a 1/16 scale of Brave Borderer approx 1800mm long. I used 8mm ply for the bulkheads and covered with 1.5mm ply with the bow section made of block balsa. I had no end of trouble trying to get the chine line correct at the bow using existing plans, but the model is too heavy so it now lives on a shelf.
Mk2 version using plans supplied by John Lambert. It was suggested that instead of using ply to skin the frame - that I should plank the frame with 3mm balsa then cover with 2 sheets of woven fibreglass not stranded matt. End result should be a much stronger hull and a lot lighter.
Am I on the right track or am I going to the Mk3 version.....at least I have learnt a lot so far
Martin from Down Under :-\ :-\ :-\
-
hi there Martin from Down Under ;D ;D ;D
I see the forward chine is causing you some (shall we say - stress) on the hull. The way it sort of bends down in an 'S' shape when looked at from the side.
To be honest with you, plank on frame is only one option for you. There is the method of using carved foam, which has been described on this forum elsewhere I think, where you carve the shape of the hull you want out of the foam, seal it with either an emulsion paint or some other material. Use a releasant on top of that, lay your matting on top of that & then finish off with car body filler and sand until you reach the desired finish.
My personal choice would be to go 'plank on frame' and for the bottom of the boat, I would diagonally plank with the thinnest and narrowest strips of wood possible, something in the region of say 4mm wide x 0.5 mm thick Obechi. For the sides of the hull I would diagonally plank that as well using maybe 10 mm wide x 0.5 thick Obechi wood.
On top of this, I would lay two layers of tissue matting, finished off with a top coat of resin, sanded smoothly.
Then, when you remove the hull from the building board and turn it over it may be adviseable to add a layer of tissue matting on the inside of the hull as well in between the frames.
I should think you would find the hull will be pretty strong after this.
Hope this is of some help.
aye
John
bluebird
-
Thanks John,
I have seen that method on the forum re diagonal planking but I have one problem with it.
Down here in Australia, I have not been able to source Obechi for sale and the thinnest marine ply when and if its available, is 0.75mm which has an extraordinary price tag hence using the 1.5mm ply.
You don't think the 3mm balsa is appropriate ?
Fibreglass matting instead of woven cloth is the way to go ?
I have been to a local supplier re fibreglass - but they have matting and cloth in many different weights - what do you suggest
Thanks again for your expertise
Martin
a long way down under
-
This may give you an idea of how to cover a hull with light glass cloth.
http://www.rcgroups.com/forums/showthread.php?t=329811
you may be able to get thin ply mail order as you will only need it in small strips have you tried http://www.pt-boat.com/ he does sheets of lazer cut ply for this purpose and is in AUS
Peter
-
Thanks Peter.
All info is good info.
Thanks for the Contact in Aust. have send john an email requestng lazer cut ply
Thanks a heap
Martin
Down Under
-
What weight or grade of cloth is used.
I will be back in UK next year and want to buy some.
Is 'Light Cloth' a grade?
TT
-
Martin,
Can you get Cedar down there? I have used this for planking in several boats, it works well and has a natural oil in it that has a water resistance.
If you can get it, just make sure that the grain in the planks is nice and straight - along the length of the plank, with little or no twists and no knots.
Ian
-
I sent off an email to pt-boat.com here in Aust and the reply is as follows:-
Hi Martin,
I can do strips for you in various thicknesses of marine ply but I don't
have 0.5mm in stock, I know I can get 0.6mm and I think 0.4mm but not
sure about 0.5mm.
My laser cutter can only cut sheets up to 12" x 18" but as I cut 1220 x
1220 ply sheets into 4 x 3 smaller panels of 305mm x 406mm strips
shorter than 406mm become the optimal length.
I usually buy Finish Birch GL3 aircraft grade marine ply, there is also
GL1 ply with no knots but it's pretty expensive.
Given that, let me know what you want and I'll get a price for the
timber and work out a price for cutting.
Regards
John Drain
[email protected]
...
Can members please advise which product is best for planking including thickness and width of strips to use on the hull - never planked a hull before, only partially in tricky spots.
I have been advised by a fibreglass supplier to use 185gsm woven cloth - does this sound correct ???
Martin :-\ :-\ :-\
Down Under
-
"Aircraft grade marine ply" ??????
I think I know what the guy means, but there's no such thing as Birch marine plywood, and there's never been such a thing as "Aircraft grade marine ply" either. Also true BS1088 marine ply, it has that identification stamped all over it, is very hard to find less than 6mm thick, and it isn't even manufactured below 4mm thick. For model boats, stick with good quality WBP (water and boil proof) birch ply, that's all you need. The only modelling use for proper marine ply that I can think of would be a heavy duty boat stand that you wanted to leave out in the rain.
-
Hi there Malcolm
To be quite honest, you have several options open to you. Which one you decide on is entirely up to you and which one suits you the best. You could plank a hull quite successfully using 3mm thick balsa strips. Planking a hull with balsa has been done by several members of this forum quite successfully. I have planked with balsa on 2-3 occasions.
The resason I dislike using balsa as a planking material is, I am very heavy handed when it comes to sanding :embarrassed: and I have sanded through on several occasions.
The way I personally overcame the problem of sanding through was, when I had finished planking a hull, before I did anything else, I coated it with a coating of polyester resin with hardener mixed in to allow it to soak into the balsa wood, making the balsa wood slightly harder and better for me to sand.
If you go the plywood way and use plywood as planking, 1mm thick plywood cut into 8mm strips would do the job. Personally, I would go for 0.5 or 0.6 mm plywood, or whichever is the best option for you.
I would cut the plywood into 8mm thick strips.
I have a friend who sat one night with a stanley knife and a steel straight edge. He marked off and cut a 4x2 sheet of 1mm thick plywood into strips for to plank with. This was just to save him the cost of having it cut for him into strips plus he did not want to waste any. O0
Now, I have included a little scribble, which may assist you in how to diagonally and double-diagonally plank your hull. Once you have all the basic framework set in, where you have your keel/chine/stringer/deck edge stringer in place - it pays you to add bottom stringers. The more you add in, the closer you will get to your bottom hull profile. The same on the sides, because the hull you are proposing to build has a fair amound of flair at the bow end.
When you eventually come to start to plank, my personal preference is to commence approximately at the centre of the hull - mid-section. Your first plank should be approximately 45 degrees angle to the keel.
As you plank towards the bow, you will note that the angle of the plank will increase. This is normal. My normal method of planking, is, to do 5 planks one side of the hull/5 planks the opposite side of the hull and by that time the 5 planks on the other side are dry (i.e. the glue has dried).
Then, I go 3 planks one side of the 5 and 3 planks the other side of the 5 (in other words 3 planks towards the bow and 3 planks towards the stern). Once they are, I do exactly the same on the opposite side.
When the hull bottom is complete with one layer of planks, I do the sides in exactly the same method - i.e. 45 degrees from the deck edge at mid-section of the hull.
Once I have the full hull completed with one layer of planking, I lightly rub it down to remove any abnormalities, fill in any hollows with P38 filler and then apply my 2nd top layer of planks in the opposite direction to the bottom layer of planks.
Once this has been done and I have sanded and filled - I then proceed and give it a coat of polyester resin with hardener mixed. This is where I think you will have to make your own mind up of what fibre glass material you are happy working in. Some of the very light woven material (similar to what the aircraft lads and lasses use) some people find it easy to work with and some find it difficult because it can be difficult to remove air bubbles out of.
If you have had no experience in working with fibre glass, it may pay you to try and work with a very light chopped strand glass mat thats for Kayem :D .
I hope this is of some use to you.
aye
John e
bluebird
-
Who is a good, reasonable price supplier of the folowing in the UK.
0.4mm ply
Fibreglas tissue (and what grade/weight should I use on a hull exterior?)
I will be back in UK in Jan and want to get some stuff to take back to china with me.
TT.
-
The resason I dislike using balsa as a planking material is, I am very heavy handed when it comes to sanding :embarrassed: and I have sanded through on several occasions.
The way I personally overcame the problem of sanding through was, when I had finished planking a hull, before I did anything else, I coated it with a coating of polyester resin with hardener mixed in to allow it to soak into the balsa wood, making the balsa wood slightly harder and better for me to sand.
If you have had no experience in working with fibre glass, it may pay you to try and work with a very light chopped strand glass mat thats for Kayem :D .
aye
John e
bluebird
Ooh, thanks John, I didn't know you cared!
On the rest of Bluebird's post, it's the usual recommendation, use whatever method works best for you, but I much prefer balsa planking to ply for this kind of thing, the planking takes a fraction of the time for one thing, and this is how I do it.
Use fairly firm balsa, not the really soft stuff, and for most hulls I'd use thicker wood, probably 5mm, or what we used to call 'three sixteenths'. This isn't too bendy, which is both a help and a hindrance, it's a little harder to work with, use a razor plane to bevel plank edges, but thicker wood will follow the hull lines better, so you're less likely to get hollows, and it gives you a lot more leeway when it comes to sanding, which is good if you're heavy handed as Bluebird claims to be. After all the glue is hard, a very light going-over with the razor plane, and then the way I sand is to use quite coarse 80 grit paper on a fairly large block, all you want to do is take off any high spots and raised plank edges, don't worry about any hollows, that way you should end up with a minimum of about 3mm of balsa everywhere, even over the bulkheads, and you should have something a lot better than it would be if you'd planked with 3mm wood in the first place. After that, I apply a coat of fibreglass resin to seal everything, but I'd hate to have to try to sand the hull after this, it would just stick to the abrasive paper and clog it, so once the resin has set, add a layer of 450gm glass mat over it. Once that's hard, you have a solid and uniform surface that isn't going to move up and down as you sand it, so apply P38 filler everywhere you can see hollows and imperfections, and sand away on that to your heart's content.
This is just the method that works best for me, but I've planked an awful lot of hulls this way with good results, so you might find it works for you as well.
-
I have usually used Kayem's method for my hulls except that, after the main smoothing has taken place, I use sanding sealer to impregnate toughen the wood before final finishing. I agree that medium to hardish grade balsa is good to work with.
-
And here's one I made earlier.
This is a 36" steam launch hull done in the way I described a couple of posts ago. Slightly different from what most of you would want to achieve, as this is only intended as the pattern for a fibreglass mould, all the bulkheads etc are solid, though with minor changes the same method would be perfectly OK for most types of hull that were to be used for a sailing model, indeed almost all of the internal structure on this one could have been removed to achieve this if I'd wanted that. Underneath are 6mm plywood full size plan and profile shapes, though without the added keel on the profile, it's better to add this later, and about ten 6mm ply formers. The midsection and transom were worked out on my drawing board, and all the others by eye using a flexible lath, a practiced eye and years of experience for a fair curve. Once that all looked OK, the hull was planked with 5mm balsa in short sections, all joined over a former, and a little like Martin's Bismarck. Where you can use this method, it's a far quicker and less fiddly process than planking with longer lengths, which is I suppose most would consider to be the 'proper' way. You might expect to end up with something rather like an old fashioned threepenny bit using this method, but the curves are such that only a bit of fairly gentle work with razor plane and sanding block were needed to end up with the right shape that I could run my hand along without feeling any unwanted corners. If you work accurately with a job like this, you should end up with a minimum thickness of around 3mm of planking in the thinnest areas. As can be seen, the bow was done with balsa block, and as the transom wasn't quite the shape I wanted, I added a second layer of 5mm planking, and planed this away until it blended smoothly into the first layer. Next steps were exactly as described previously, a coat of resin to seal the wood, a layer of 450gm mat to make everything good and solid, infinitely better than glass tissue which has no real strength at all, a couple more coats of resin containing an additive so it sanded better, then filled as needed with P38 and sanded again to a nice smooth finish. After the keel was added, what you see here is ready for the final finishing coats of resin, and I can't imagine any faster way of getting a result like this.
-
Just to throw more fuel on your fire Martin 13, the last skinning I did ( All be it on a PSS SR71 ) was by using
Epoxy Resin and Silk. Silk used to be easily obtainable in lightweight grades when we used to have at least two
model shops in EVERY town over here. I had to go to the local Asian material importers, (Dress Material) for mine.
-
Hi all
As we can see, we have two versions now, of how to produce a hull and YES there are many other ways of producing a hull which we have to bear in mind.
What we have to take into account is that everyone has their own preferred method of producing - I know one way of making Kayem and I run 100 miles :) and that is, if you were to give us sheets of Plasticard, and, then tell us to make a hull out of that. No doubt we would have a good go, but, I do know what we would prefer to use instead of Plasticard.
Anyway, the only thing I can comment on about Kayem's method is, when you produce a hull using double diagonal out of either balsa wood/obechi/plywood you are building in an added strength by having the grains of the materials running at 90 degrees to each other. That has far more impact strength than the grain running in one direction only. When I build a lot of my hulls of double diagonal, I only use the tissue mat, as Kayem has said - it gives no added strength to the hull, its only there to seal it. As the strength comes from the double diagonal build.
I have attached a couple of photographs of a hull which I built not so long ago, for the Fairmile B, and, as you can see, the inner planking is Obechi and the outerplanking is 4mm x 0.5mm thickness mahogany and this was coated with an Epoxy system SP, no matting was used whatsoever. This will also show you the type of finish you can obtain by using Epoxies.
Epoxies tend to be a bit more expensive than polyesters - but be careful, some epoxies are not very user friendly. I know one or two people who are very allergic to the substance. When they use it they have to be dressed up like a NASA astronaut.
Aye
john e
bluebird
-
Never thought about allergies John, cheers, you've just explained why I've got six digits on one hand and eight
ont other!
Kayem, is that chopped strand matt (sorry - mat) on your hull build?
Ian
-
This will give you an idea of the cloth used in the link I posted. It is very light in weight, I think the method that kayem was using was for a mould where weight is not a factor, if you use ply have a look at the PT boat site and he gives info on what he uses for a hull of similar size to your's, and then it's just down to waterproofing with the fiberglass.
Peter
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXAU14&P=ML
-
tigertiger
The best ply I have had of late was from http://www.jperkinsdistribution.co.uk/ But I tend to buy a few sheets at a time and keep it on stock so they don't mind sending it to me , send them an e-mail and tell them your situation and they may be able to tell you who stocks it in the are you will be in , and you can then Pre order, most shops stock ply of that size but jperkins tend over the years to be the most consistand in quality.
Peter
-
This has been a really usefull thread with lots of great info. O0
Kayem, I would never have thought of doing things your way, with short thick strips. This makes life really easy. :D
Bluebird, I understand your point about weight. as I want to build scale sail, where keeping the weight below te waterline is important due to heeling forces. :D
HS 93 thanks for the links, I will contact them. O0
Now I would like some advice please ;D
On my next planned build (Arab Dhow) the planking will show and I want it to be a bit rough. I was thinking of 3mm balsa plank, coated in resin afterwards with F/glass tissue or matt internally between frames for added strength. The hull is about 600mm overall length.
Will this work.
In the future I will be building larger hulls between 1m and 2m. These will be for scale sail and the planking will not be showing.
Do you think 3mm will be strong enough in this instance?
Would 5mm to too difficult for some of the curves?
would using matting externally be too heavy?
I look forward to opposing views at the debate here so far has been very informative.
Thanks again.
TT
-
Here are a few comments on a few of the comments that followed my last post.
Firstly, this is only one way of doing the job of producing a fibreglass skinned wood hull, and if some other method suits you better that's fine. I've tried most of the alternatives, all have good and bad points, and this is just the way that suits me best. It's relatively expensive on materials, but I find it by far the fastest method, and when you're doing this kind of thing for a living, time is money. To succeed, you do have to be able to make joints really accurately, never rely on adhesives to fill gaps, both edge to edge joints and end to end, but it's much easier sanding and planing slivers from a 4" length of 5mm thick wood than trying to get a perfect fit with a thin plank that runs from bow to stern, twisting along the way. Bluebird was right about one thing, ask me to build a hull with styrene sheet or Plasticard, and I'd run miles, probably something like double the hundred he suggested.
Peter suggested that this was a heavy method, but I don't think it is. My hull in the pic is heavy, but much of the weight is in the 6mm ply internal structure, which wouldn't be there in the case of a sailing model, and wanting to end up with something fairly robust, I was fairly generous with the glass and resin. If you think about it, my hull is one layer of 450gm glass mat, much the same as any bought hull, the fairly thick balsa planking weights very little, and the internal structure need be no more than any other model with a built-up hull, 3mm ply would have been quite adequate for all the formers etc. There isn't a lot of P38 filler used, and it's mainly at the rear end where I decided to modify the original shape. This method works well for hulls with tighter curves, but you'd have to space the formers closer together, though possibly this would only be needed at the bows, and then you'd use shorter planks between them of course.
A couple of tips I've just thought of, It is important to seal the balsa completely with resin before applying the glass, you'll probably need a couple of coats. Covering curved shapes neatly with fibreglass is a skill that comes with practice, once you develop a feel for working with the stuff, you can both shrink and stretch glass mat with deft use of a brush and a suitable roller. There was no external keel on my hull when I added the glass mat & resin layer, so I was able to cover the entire hull with a single piece, it only needed two or three smallish vertical cuts and overlaps along the deck edge on each side and at the bows. The small double thickness areas that result are easy to sand away once the structure has hardened, but just about the best advice I can give to any modeller is to only ever use abrasive paper on a suitable shaped sanding block, that's the only way you'll ever achieve good results.
-
hi there TT
The only problem I could foresee with planking the hull of The Dhow with balsa wood, if you do not coat the outside with either dope or a resin, it is going to leave it vulnerable to knocks and scratches which, once the water penetrates, the balsa wood would swell rapidly.
I can understand your problem of sourcing materials where you are living - however, since the model is going to be in the region of 24 inches long, how's about building the hull from balsa wood as Kayem has suggested. Have a smooth hull and then covering it with a tissue or a light mat. Then assimilating the planking with either Plasticard or a thin veneer/even thick card, which you could seal with either paint or a varnish.
This would give you adequate protection.
aye
john e
bluebird
-
Thanks Kayem
points noted.
Thanks Bluebird.
Am I right in thinking that a layer of tissue soaked in resin would still be largley opaque?
TT
-
Hi ya there TT
have a look at this photo it may give you some idea. The hull has 3 coats of resin with tissue mat on.
As you can see, you can still see the planking underneath.
However, and this is the big however, polyester resin is not waterproof. After a prolonged period in water. it will start to absorb water. This is why, on full sized hulls, you use a gelcoat on the surface that is going to be in contact with the water.
So, when we use it on our models, we must coat it with either a varnish or a paint.
Hope this is of some help.
Aye
John e
bluebird
-
Am I right in thinking that a layer of tissue soaked in resin would still be largley opaque?
TT
That hull in my pic has a layer of 450gm mat, 'ounce and a half' measured the old way, and you can see all the wood grain through it. You can't get much more transparent than that, and glass tissue of course is very much thinner. Always wear rubber gloves, something like those yellow Marigolds, whatever type of resin you're using, they don't feel clumsy once you get used to them, and as Bluebird mentioned, be very careful with epoxy resins, this seems to be a very common and quite serious allergy.
-
Hi Bluebird.
Are there limitaions on what type of paint/varnish I can use?
Is epoxy resin waterproof?
-
Hi there TT,
I dont think there would be any limitations, as long as the paint is waterproof and the fibre glass is prepared correctly for painting. I normally use either Humbrol, Tamya, Halfords' spray paints etc., and I have had no problems with these peeling off.
Epoxy resin, yes, is waterproof - but, please be careful. As Kayem & I have both mentioned = some people do develop allergies with this stuff. Allergies vary from severe skin rashes to actually effecting respiratory system i.e. breathing can become difficult in some cases fatal, so be very very careful and heed all warnings on the instructions. Like a lot of things in life, some folk can use them and not be bothered with them one little bit, but its not worth the risk - use all precautions - treat it as a deadly enemy and with great respect.
aye
john e
bluebird
-
I am shore some of our paint people will put me right, but a mate of mine who is in the paint trade told me at one time that the only paints that where not porous where Two pack paints, I went in to this when trying to seal my fire tender and everytime I suggested a type of paint that we use he said it was not. as it was air drying or something.
Peter
-
I think it's true to say that NOTHING is truly waterproof - there are just degrees of water resistance. Epoxy finishes are up there at the high end. However. model boats spend only a fraction of their total life afloat so most modelling paints, enamel or acrylic, are quite suitable as a final finish. The danger, as as already been mentioned, is that if the paint film is broken due to a knock or a scrape, water can get to the underlying surface which should be "waterproof" in it's own right - i.e. sealed with resin or sealer etc.
-
This is one of my better threads - must say a big thankyou to all on this subject matter.
HS93 Peter - thanks for the info on links - very informative.
Kayem and Bluebird - I like both methods that have been put forward and seeing that I have the Mk1 and Mk 2 hulls, I'm keen to try both methods of skinning and fibreglassing the hulls to see what works best for me.
After all, what's the worst thing that could happen?
I'll build another one (Mk3)
Quoting Monty Python - it fell over, burnt down and sunk into the swamp !!!!!
Finally received a copy of the Glassfibre Handbook in the post - Highly recommended - You can never have too much information.
Its good to see that other forum members like TigerTiger have gained knowledge and in some cases preempt my thoughts
Now - can someone please tell what is P38 Filler and what does the abbreviation SWMBO mean ???
Thanks again everyone.
Martin in Aussie land
-
SWMBO
"She who must be obeyed" (the missus"
Ken
-
what is P38 Filler
Easy sand version of car body repair filler. If you use the harder versions there is a danger that the surrounding hull will sand down quicker than the filler leaving a proud spot. P38 also sticks well to most things.
-
Gosh I love this forum stuff.
I asked the guys at work what SWMBO meant and couldn't tell me - they will love this one - thanks Kenny.
Colin - I fell for that trap on my Mk1 Hull where the filler was proud of the surrounding timber.
Is P38 a brand name ??
-
I think P38 used to be one of Isopon's branded fillers.
Get in in Halfords I imagine.
-
P38 is a brand name see here: http://www.ppc.au.com/fills.htm
There are other brands of polyester easy sand paste filler you should be able to get hold of quite easily though.
-
Gosh I love this forum stuff.
I asked the guys at work what SWMBO meant and couldn't tell me - they will love this one - thanks Kenny.
Colin - I fell for that trap on my Mk1 Hull where the filler was proud of the surrounding timber.
Is P38 a brand name ??
There's an amusing footnote to this, the first time I ever heard the expression SWMBO was quite a few years ago on a wonderful TV series called 'Rumpole of the Bailey', uttered regularly in reference to his rather forbidding wife by the late Leo McKern, a much loved actor who died only quite recently. The amusing bit comes from the fact that Leo was an Australian born in Sydney, so most of the UK probably thinks that the expression SWMBO originated in Australia. But apparently not, so 'fair dinkum' to you.
-
Rumpole
Leo was a great actor;
Born March 16, 1920
Sydney, Australia
Died July 23, 2002 (aged 82)
however he didn't write the script...that was a posh London type..John Mortimer...
People don't really think they make up the words as they go along..do they?
-
People don't really think they make up the words as they go along..do they?
What??? You're telling me that they don't ????
Valerie Singleton once had to sweep elephant turds off the Blue Peter set, she told me so herself, so what's the difference?
-
TT for your cloth it may be worthwhile looking here
[urlhttp://www.fibretechgb.co.uk/DefaultHome.htm][/url]
I use them a lot for aircraft builds and also for hull building . I dont know how it fits into your plans for a UK visit but they are great on postage to the Uk so if you have an addy here for them to send to it WILL be there for you to collect from O0
HTH
Shane
-
Bluebird - John,
With regards to the intermediate stringers as per your drawing, what width material do you suggest and should I use a soft or hardwood ???
Thanks
Martin
-
Martin, hi there,
On the size of hull you are building, I would use between 5mm square and 6mm square intermediate stringers, around about that size.
Softwood may steam and bend better to get the right curves in the hull as you come towards the bow.
If you want to use a hardwood, what you could do, is, use 2 pieces, 3mm x 6mm wide laminated together to give you the 6mm square. However, obviously, you would first have to glue one piece of the 3mm x 6mm timber onto your frames first. You would then have to glue the next piece on the top of it.
Hope this is of some help..
aye
john e
bluebird
-
Hi John - Bluebird,
Thanks for info on stringers - had a feeling about the size.
In the recent past whilst working on a glider wing using CA glue, I had a god like thought that I could walk on water - I sunk !!!!
After that experience, I installed a dust and fume extraction system to my workshop. In one corner I have a 20 inch planner-great toy.
With regards to using resin, a fibreglass supplier suggested that I use epoxy resin instead of polyester resin stating that their is less chance of shrinkage and cracking over time.
I was also advised that whilst curing, I needed to keep the temperature around 20 degrees Centigrade otherwise it will not cure correctly and remain tacky.
Your thoughts.....
martin
-
hi ya Martin
With regard to your question about using Epoxies and Polyester resins; to get the true answer for yourself, i.e. as to which one is the best; you will basically have to work with them both over a period of time.
They both have advantages over one another; and of course disadvantages; these are my thoughts on it;
Polyester Resins
These require a stable temperature to work in, as you have noticed, say round about 20 degrees Centigrade, but no lower than about 15 degrees Centigrade. The hardener to resin mix ratio is pretty critical.
Compared between the two, pricewise, it is the cheaper one. For what we are going to use this polyester resin for, e.g. modelling, it fills all our needs quite easily. We do not keep our models in the water for great lengths of time (as in weeks on end :) ) So we need not really worry regarding water being absorbed into the polyester, because, in normal circumstances there is a protective coating over them e.g. varnish.
Before polyester resins start to absorb water they have to be submerged for at least 2-3 days.
With regard polyesters shrinking and moving; all plastics do this, even Epoxies. Some at a greater rate than others.
You have got to think about your application of the Polyester; you are not planning on building a great thickness of matting and resin up on your hull, e.g. something over 5mm. So, therefore, I would not be too concerned about it moving and cracking, because, do not forget, any form of timber as well would expand and contract as well under working conditions.
Where problems surface is if we coat one side of the timber with matting and resin and leave the opposite side open to the environments. This is because, if the timber side becomes damp, it will expand at a far greater rate and therefore delaminate from the polyester resin. So, that is why it is always adviseable to give the inside of the hull a coating of resin as well as the outside. This actually seals the timber.
The only major problem occurs when you build up a mass of fibre glass e.g. I have seen around bottoms of hulls and also rudder posts where people have laminated and poured resin in, to something say one inch thick, they think they are adding strength and this is where the polyester starts to deteriorate, move and crack.
Epoxy Resins
There are several grades of epoxies. Several names too. No doubt you will have heard of what is called 'The West System' which was the first system really developed for Marine Use, but that is the 1:1 scale Marine Use. It is one of the highest water resistant epoxies and also one of the most expensive. It's mix ratio is also critical - from the top of my head I think it is 3-1 mix ratio, i.e. 3 parts epoxy to one part hardener. Sometimes to maintain this mix ratio, you have to purchase the correct dispensers.
Working with this - it is much the same as Polyester resin - its like a thin treacle. It is not so temperature critical either, some specialised epoxies can be used in temperatures just above zero. But, these are specialised epoxies. It does have a less shrinkage to it, for arguments sake, let us say one inch square stick of polyester resin would expand 1/8 of an inch at 50 degrees. One square inch of epoxy resin would only expand about 1/32 of an inch at 50 degrees. These figures are not exact, but, just to give you some idea. One of the major drawbacks is its price. I think it is twice the price of a polyester resin.
Also, it is a slightly more hard resin, it withstands impacts and indentations at lot better than polyesters. How do I know this, :embarrassed: the concrete at the side of the lake is very HARD a lot harder than polyesters and epoxies put together {-).
I suppose last but not least at all there are health warnings that go with them which I believe we have mentioned elsewhere.
So, to be honest with you, its another case of, the choice is yours, if you are prepared to pay that little extra for the Epoxies, it will give you a longer lasting hull. If your hull is going to endure all different environments.
However, if you are just going to use your model say a couple of times a week on a standard lake, but from the pictures I have seen of some of the lovely lakes you have in Australia, we would class them as an Ocean {-) {-) - the choice again, is yours.
Hope this is of some help to shed a little light.
(Please be aware though, I have just skimmed lightly over this topic).
Aye
John E
bluebird
-
Hi there Martin,
Curing times
Once the resin has 'gone off' (normal working time for working with polyester resin is between 20-30 minutes meaning resin in the pot). The resin starts to cure as obvious.
At 20 degrees Centigrade, this should take between one-two hours at the most for the resin mix to set hard.
At 20 degrees Centigrade, it should be fully cured in about 3 hours.
If you are concerned, after the resin has 'gone off' and the smell has gone - you will know what I mean about that :D - and without telling 'SWMBO' - move it into the house into room temperature and leave it there for a couple more hours.
hope this helps
aye
john e
bluebird
-
and without telling 'SWMBO' - move it into the house into room temperature and leave it there for a couple more hours.
And then a few hours later the divorce papers are put in your hand. >>:-( >>:-( {-) {-)
-
Make an open topped mdf box to go over your hull, with the open side downmost, place hull and box on a workmate with the jaws part open, place low power greenhouse heater (electric only) underneath, leave for 24 hrs, no need to turn ;) and your hull and epoxy will be well cooked and hardened.
NO gas or oil fired heater - they produce a wet heat.
Works for me
Ian
-
John, you skim well - thanks again and again.
Boatmadman/Ian
Along time ago where I was once employed, we had a small spray booth at work and when the job was completed, we placed the items in another small booth and turned on incandescent lights for drying. I imagine this will have the same effect as per your suggestion.
As for the low power heater, what rating do you suggest - wattage.
Ron1, My wife puts up with a lot (but I deserve it), should I bring the hull into the house and tell her that there will be no smell or leave stains on the carpet, her response will be as per this riddle: -
What do you get if you cross a Bulldog with a Shi Tzu ?
Martin
-
Bluebird / John,
Recently I visited a manufacturer and retail outlet of fibreglass products with photo's of my model hull and explained to him the problems I was having.
He suggest "Epoxy Bond Fibreglassing Resin 430" and another product "Q-CEL 5020, Sodium Borosilicate Hollow Microspheres.
It was recommended that I mix the Q-Cels with the Epoxy resin to make a paste like substance and coat the bow area hopefully correcting the imperfections.
Check out their website http://www.solidsolutions.com.au
they have a 2 night course on fibreglassing and mould making - do you think I should attend ????
Martin
-
and without telling 'SWMBO' - move it into the house into room temperature and leave it there for a couple more hours.
And then a few hours later the divorce papers are put in your hand. >>:-( >>:-( {-) {-)
There's a very simple solution to this, once your polyester/epoxy laminate is touch dry, wrap it in polythene, a large bag or bin bag will do, tape up the ends, and that cures any smell problem. Then bring this into the house and leave it against a radiator for a day or two. It helps if you turn it from time to time so it 'cooks' evenly. The technical term for this process is 'post-curing', industrial users have proper low temperature ovens, but this small scale domestic solution works just as well. Never rush anything like this, you've probably spent weeks working on the job, so an extra day isn't going to make a lot of difference. An awful lot of modelling moulding disasters that I've been told about were caused largely by impatience on the part of the modeller, it isn't a process that can be rushed.
-
Good day Martin
Personally, if it was me, I would definitely attend a two nights' course in fibre glassing. It may not cover exactly what you want to do, but it should give you the confidence in working with fibre glass. Possibly it will also answer a few of the unforeseen questions which everyone comes across. :)
aye
john e
bluebird
-
John e,
I called the company yesterday re attending one of their classes but unfortunately the course is only ran the first week of each month and currently booked out till mid next year.
Oh well, looks like back to the trial and error method.
Currently 5.45 am Aussie time - must prepare for work -
Cheers Martin from Down Under
-
G'Day to all,
Unable to get a response from the thin plywood supplier - oh well, doesn't matter.
I wish to say thanks to all for your input on this thread and to all that sent pm's - I've had a few, and am very grateful for all the ways to complete the task at hand.
Seeing that I cannot currently get hold of thin ply, I have decided to go with the balsa method of construction prior to glassing and try not to be heavy handed (found 50 sheets plus on a shelf).
When I have gained more experience , I would really like to try the diagonal planking method - it looks great but the only thing is, If I was able to make it look like Bluebirds model - it would be a crying shame to paint over it............
Thanks again to all for your patience and input - it is much appreciated...
Martin from Down Under
just for interest - local time 1945 Hours
-
G'day my mate and how's the roos and wallaby's todoy then? ;D ;D
hI YA Martin from doon under!
There is really nothing stopping you having a go at double diagonal planking with balsa wood. Obviously, the first layer of planking you would not need to put any resin on that, but, just be very careful when sanding and use blocks of wood of various shapes and sizes to wrap your sandpaper around when sanding.
I use several of these blocks of wood of varying shapes and sizes from half round shapes to wedge shapes & so on. You will find that you end up with a collection of block pieces of wood that you can never find when you want them to use as sanding blocks, but, do not forget one major thing when you start to build PLEASE PUT A BUILD THREAD ON HERE WITH PHOTOGRAPHS and then we are kept informed of how you are getting along with your build.
BEST OF LUCK.
John
-
Hi again Martin
Whilst doing some research for another project, I came across Model Boat Magazine December 1976 and this runs an article on Making a Model using balsa wood as frames, and double diagonally planking it with cereal packets cut into strips.
A quick read through, it would seem as though the cereal packets are cut into something like 10mm wide strips, to be used as the planks and the model is planked diagonally - when the first layer of planking is complete - it looks as though it may have been coated with either a polyurethane paint or a sand n sealer and then the outer layer is applied. Obviously planking in the opposite direction and then over the top of this, they are talking about applying a coat of mat/fibre glass cloth and if you are interested, let me know I will see if I can email the articles to you.
IT MAY BE WORTH LOOKING AT O0
I do know Colin (Bishop) has built serveral models in a similar way, but, what materials he uses I am unsure. Maybe Colin can come in and explain.
Food for thought my Friend.
aye
John e
bluebird
-
For the old hands from the Model Boat forum, this is mmgemini's cardboard Thames barge. A good example of what you can do with cornflakes packets.
-
Hi there,
Yes, Marc, I forgot all about Mike - I am not sure if he still comes on the forum now??? Mike has a wealth of experience and information of building models out of different materials. I think he may be in Africa now, driving his Land Rover? somewhere :D
aye
john e
bluebird
-
G'Day to all
It absolutely amazes me what you people come up with. Not in a million years would I have thought about using Cornflake packets :o
Would it be suitable considering the size of my model ?
John, I have printed out a copy re your photo of diagonal planking and have it on my wall in my workshop - I use it for inspiration.
And yes, interested in anything you can supply on the subject.
Build Thread - After spending many many years in Avionics within the commercial and military fields, coupled with large amounts of stress, resulting in severe brain strain - my head hurts :( :( :( and have now entered the area of brain shut down with respect to anything to do with computers and electron flow.
Basically what I am trying to say is, I am hopeless with personal computers and digital cameras (I prefer my Nikon SLR) coupled with the fact that I am rather slow with modelling due to swmbo input >>:-( >>:-(. But if the forum doesn't mind the thread running a little slow - I will con the swmbo into photo taking and posting onto forum - after all, she's the IT expert.
Thanks and Thanks to all
Martin from Doon Under O0 O0 O0
-
I've not actually used cornflake packets but that sort of cardboard if impregnated with dope/sanding sealer or shellac is a perfectly good material for coating hulls. My preferred method for liner type and similar hulls is to build the basic structure of composite balsa. By composite I mean "economical". As the bottom of the hull is usually flat then you start with a suitably shaped piece of sheet balsa upon which everything else is built. The next bits to go on are the stem and stern frames in plywood. I usually cut a groove in the stem to accept a length of brass bar so that when you hit something you don't take a bite out of the stem profile. The midships body is usually parallel sided so I put a balsa bulkhead at each end and use sheet to make up the sides with a substantial square fillet along the bottom to allow for the turn of the bilge to be carved without going through the material. The extremities, bow and stern are usually block balsa while the bits in between where there are curved profiles are dealt with by a bit of plank on frame using extra bulkheads mounted on the bottom section to give the right shape.
The whole thing is then carved and sanded to shape but not sealed. I then use gummed paper strip to coat the hull, laying it along the hull to simulate the inner and outer strakes of plating. Instead of wetting the gummed paper with water I use Cascmite/Extramite water based resin glue which bonds the gumstrip to the underlying balsa. As gumstrip contracts very slightly as it dries you get a very tight fit to the hull. The next step is to paint sanding sealer or shellac onto the gumstrip which impregnates it and makes the whole thing waterproof and solid. It rubs down to a superb finish very easily. Then complete the job with your favourite paint finish Humbrol, Halfords or whatever.
-
Hi there Martin
If you go the plywood way and use plywood as planking, 1mm thick plywood cut into 8mm strips would do the job. Personally, I would go for 0.5 or 0.6 mm plywood, or whichever is the best option for you.
I would cut the plywood into 8mm thick strips.
Now, I have included a little scribble, which may assist you in how to diagonally and double-diagonally plank your hull. Once you have all the basic framework set in, where you have your keel/chine/stringer/deck edge stringer in place - it pays you to add bottom stringers. The more you add in, the closer you will get to your bottom hull profile. The same on the sides, because the hull you are proposing to build has a fair amound of flair at the bow end.
When you eventually come to start to plank, my personal preference is to commence approximately at the centre of the hull - mid-section. Your first plank should be approximately 45 degrees angle to the keel.
As you plank towards the bow, you will note that the angle of the plank will increase. This is normal. My normal method of planking, is, to do 5 planks one side of the hull/5 planks the opposite side of the hull and by that time the 5 planks on the other side are dry (i.e. the glue has dried).
Then, I go 3 planks one side of the 5 and 3 planks the other side of the 5 (in other words 3 planks towards the bow and 3 planks towards the stern). Once they are, I do exactly the same on the opposite side.
When the hull bottom is complete with one layer of planks, I do the sides in exactly the same method - i.e. 45 degrees from the deck edge at mid-section of the hull.
Once I have the full hull completed with one layer of planking, I lightly rub it down to remove any abnormalities, fill in any hollows with P38 filler and then apply my 2nd top layer of planks in the opposite direction to the bottom layer of planks.
Once this has been done and I have sanded and filled - I then proceed and give it a coat of polyester resin with hardener mixed.
I hope this is of some use to you.
aye
John e
bluebird
John/Bluebird
I have decided and started to use your method of double diagonal planking for two reasons:-
1. I'm busting to try this method - something new ;)
2. Due to size of model and that it is a planing hull, it needs to be quite strong and I don't believe balsa will give me the strength in the hull
As per you method, I have started to diagonal plank the hull beginning from the centre.
Currently I have about 20 strips laid on the bottom 10mm x 0.6mm plywood and am surprised by the strength in just one layer. I can see this is going to take some time to complete but I'm in no hurry and am enjoying another way in skinning a hull.
Is it necessary when laying the strips to glue the edges (not easy to get glue on the edge of 0.6mm material successfully). Currently I am getting glue oozing out and building up on the surface of the planks which will need to be sanded off prior to fixing second layer.
Your advice would be much appreciated,
Martin doon under ;) ;) ;)