Model Boat Mayhem
The Shipyard ( Dry Dock ): Builds & Questions => Working Vessels => Topic started by: canabus on September 25, 2018, 12:20:15 pm
-
Hi All
Building my first strip plank boat !!!
Side on looks the same as the Eileen and Hellen Fishing Boats, but with a lot more beam(same length ).
As it has a raised area forward of the wheelhouse and a larger hatch, it will have better access into the hull.
Ordered a Raboesch 60mm 3 blade prop, HPI Rock Crawler 55 Turn motor( only running on 40% throttle on 2S Lipo battery).
This is the same setup as in my two Hellen boats.
Also ordered from Hobbyking a Hobbywing Quicrun 60Amp ESC( these have links for battery setup and NO BRAKE).
Straight forward and reverse( no stopping on changing direction).
Canabus
-
Hi All
Using Ikea wooden blind for planking, better than balsa, cheaper, stronger and steams well for bending.
Canabus
-
Hi All
Just about finished planking also working on the wheelhouse and hatch.
CANABUS
-
Very neat first go at strip planking! :-))
Looking good!
Andy
-
HI All
Finished planking up to deck level and fibreglass inside and a coat of resin on the outside.
A few hours on the sander next !!!
Canabus
-
HI All
Got the corner sections on the wheelhouse installed and made the boat stand.
Canabus
-
Hi All
Well it's time to raise the bulwarks!!!!
Canabus
-
Hi All
Finished the dingy and bulwarks.
Also the hatch, skylights and companion way.
A bit of paint with matt 131 green and matt37 for the bottom with a few touches of red and yellow.
Matt vanish on top of the hatch.
Pick up a 35mm(540) brush rock crawler motor 60 turn, a bit slower rpm than the 55 turn.
Big 60mm 3 blade brass prop ordered.
Canabus
-
Hi All
Installed 14 and 1/2 pound of ballast, rudder with oiler, servo, linkage and motor.
First coat of Matt 37 and found a few spots more to fill.
Canabus
-
Hi All
Zip down to the local boat ramp and ballast tested the hull.
Added another pound and half to total to 16 pound.
No leaks !!!!
Canabus
-
Hi All
After her first dip, I have installed the deck and filled around the edges.
Next up is planking, this may take a while.
I did receive the prop and gave the hull it's first power run.
50% throttle and still over scale speed.
Good turning circle and handle the small waves like the boat should!!!
Canabus
-
Hi All
Started veneer planking the deck and added 50 LED lights in the boat.
Canabus
-
Hi All
More planking on the deck, it's taken longer than I thought!!!
Trying to match the deck planking to the wheelhouse.
Maybe a bit over the top for a fishing boat!!!
Canabus
-
Hi All
Finished deck planking !!!
The weather for the next is 20 to 30 degrees, so two coats of wood sealer and two or three coats of matt vanish.
-
Hi All
21 degrees yesterday and 28 today !!!
Two coats of sealer with sanding down between coats.
Today two coats of matt vanish.
Deck finished, onto the wheelhouse.
Canabus
-
Hi All
Working on the wheelhouse and adding LED lights to the boat.
Canabus
-
hows the build going :}
-
Hi Coastie
Things have slowed down for the Christmas/New Year, but back on track next year.
Also I was given a Precedent Perkasa unfinished(I am the fourth owner) from a club member as his heath is not the best at present.
So I have been working on getting in the water.
https://www.youtube.com/watch?v=9fddqnbnlrQ
Still a lot to go on the boat.
Canabus
-
:-)) :-)) :-)) :-)) :-))