Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Oh dear, which wire to cut? Mission Impossible moment...  (Read 2520 times)

andyn

  • Guest
Oh dear, which wire to cut? Mission Impossible moment...
« on: February 20, 2009, 02:22:25 pm »

Wanting to convert a servo to a winch, by cutting out the Potentiometer. I'm pretty clued up on how to convert servos, but I want to keep it all in the original box, and as the pot supports the final drive, it will need to remain in. Question is, can I just cut the wires and be done with it, or do I need to solder two of them together?


Logged

John W E

  • I see no ships !!
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 8,813
  • Location: South shields
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #1 on: February 20, 2009, 02:28:41 pm »

Hi Andyn
this may help you out
http://www.kronosrobotics.com/an116/GAN116_3003.shtml

john e
bloobs
Logged
Knowledge begins with respect
But fools hate wisdom and discipline

andyn

  • Guest
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #2 on: February 20, 2009, 02:38:33 pm »

Thanks very much :-))

Just had a look at the geartrain after reading that, and the servo I'm using is far more simple, and all I have to do is lop the top of the Pot shaft off and it *should* work...
Logged

andyn

  • Guest
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #3 on: February 20, 2009, 03:03:39 pm »

Success :-)) Thanks Bluebird O0
Logged

Martin (Admin)

  • Administrator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 23,359
  • Location: Peterborough, UK
    • Model Boat Mayhem
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #4 on: February 20, 2009, 05:02:19 pm »

... and he's got clean fingernails!  :-))
Logged
"This is my firm opinion, but what do I know?!" -  Visit the Mayhem FaceBook Groups!  &  Giant Models

andyn

  • Guest
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #5 on: February 20, 2009, 06:00:12 pm »

Yup, thankfully it was full of silicon grease which does have a cleaning effect O0
Logged

Umi_Ryuzuki

  • Guest
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #6 on: February 20, 2009, 07:35:05 pm »

I drill out the gear that sits on the pot shaft,... same effect, the pot can not be driven.
But I also plug the servo in, and center the transmitter sticks and trims, and then turn
the pot till the servo comes to a stops. Then I apply a drop of cement to the pot shaft
so that it will no longer shift.  :-)
Logged

andyn

  • Guest
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #7 on: February 20, 2009, 08:28:03 pm »

My servo was an old one, and very simple, the pot shaft was about 1/4" long, with a flat filed at the top. cut the flat bit off and it went into free rotation, then I had to take the end stop off, which involved filing some new teeth into the gear. Now rotates happily making a low humming noise. If it had a face, it would be rather cheerful O0
Logged

malcolmfrary

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 6,027
  • Location: Blackpool, Lancs, UK
Re: Oh dear, which wire to cut? Mission Impossible moment...
« Reply #8 on: February 21, 2009, 12:03:21 pm »

Some servos drive the pot via an insert in the bottom of the main output gear - this is even easier than drilling out. 
If you prefer, the pot can be removed as it does no supporting. 
It can be an advantage to re-site it where it can be got at without removing and stripping the servo.  some pots are held by friction, some have a collar nut, some are clipped in.
Logged
"With the right tool, you can break anything" - Garfield
Pages: [1]   Go Up
 

Page created in 0.09 seconds with 22 queries.