Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: servo winch position in relation to tx position  (Read 2795 times)

chromedome

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 231
  • Location: scotland
servo winch position in relation to tx position
« on: November 07, 2006, 08:57:05 pm »

help please...can anybody tell mewhat position the winch should have the sails in,when the l/hand lever on the tx is in the mid position?
hope this makes sense :-\

  chromedome
Logged

boatmadman

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,703
  • Location: South Cumbria
Re: servo winch position in relation to tx position
« Reply #1 on: November 07, 2006, 09:03:31 pm »

I take out the return spring on the winch control lever, and set it so that when the lever is pushed away from me, the sail winches in (goes faster) and vice versa for pulling the lever back. This also means that you can set the sails at any position and let go of the lever.

Hope this helps

Ian
Logged
if at first you dont succeed.....have a beer.....

andywright

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 544
  • Location: Upper Boat, Pontypridd, S Wales
Re: servo winch position in relation to tx position
« Reply #2 on: November 07, 2006, 09:33:46 pm »

Down for in and up for out, a boat goes faster on a broad reach, thats about half way.Most racing boat skippers set up the winch like this.
Logged
Navigational Aids vessel Master. Old Conway 70-72

chromedome

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 231
  • Location: scotland
Re: servo winch position in relation to tx position
« Reply #3 on: November 07, 2006, 09:55:22 pm »

thanks lads...I think i am not far off those settings you both suggest.

chromedome
Logged

JayDee

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 957
  • Model Boat Mayhem is the VERY Best !
  • Location: Warrington Cheshire.
    • JOHN DOWD
Re: servo winch position in relation to tx position
« Reply #4 on: November 07, 2006, 10:00:24 pm »

Hello
With the TX stick fully back towards you, the sails should be pulled right in.
Make VERY sure that the Winch is NOT stalled, in this position, it is possible to set things up wrongly and have the Winch pulling against the sails and overheat it and run the batteries down.
Model yachts don't sail much with their sails pulled hard in, so I set mine with the TX trim set to full in on the winch and sail with the trim in the mid position.
If the stick is set up WITH the trim set full in, there is no way to stall the winch while sailing.
Easier to do than explain !!!.
John.  :-\
Logged
My Projects, Photos and Videos
http://www.john-dowd.

tigertiger

  • Global Moderator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 7,748
  • Location: Kunming, city of eternal springtime, SW China.
Re: servo winch position in relation to tx position
« Reply #5 on: November 08, 2006, 02:02:55 am »

Your set up may be different.
I am using a futaba sail winch and futaba attack two Tx

With the TX full back, and with the trim full back my sails are set at about 10-15 degrees from the centre line of the boat. Which is as far in as I want them. Compl;etely in and the boat is going nowhere. With my set up, full out (85-90 degrees) is achieved with stick and the trim fully forward.

I don't have ratchet fitting on my tx lever, but by using the stick and the trim I have 6 basic sail settings anyhow.
The wind changes so quickly where I am it is pointless try to 'set' the sails for more than 5 meters. ::)
Logged
The only stupid question is the one I didn't ask
Pages: [1]   Go Up
 

Page created in 0.099 seconds with 22 queries.