Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: 1 2 3 [4] 5   Go Down

Author Topic: TAMAR Speedline 1/12  (Read 42270 times)

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #75 on: October 12, 2018, 06:37:47 pm »

Hoi Adrian ..

I'm also looking for the right drive for the 1/12 Tamar and again and again the Emax 4030 is called..

but unfortunately I can not find him anywhere .. !!
is there an equivalent alternative .. ?? also from the price .. ??

Greeting Holger

Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #76 on: October 12, 2018, 07:53:32 pm »

Hoi Adrian ..

I'm also looking for the right drive for the 1/12 Tamar and again and again the Emax 4030 is called..

but unfortunately I can not find him anywhere .. !!
is there an equivalent alternative .. ?? also from the price .. ??

Greeting Holger


Hi Holger. It would appear that that particular series of motors are discontinued. I found this page that attempts to provide equivalents but they may not be exact
https://www.4-max.co.uk/equivalents-e-max.htm
Logged
ANDY
You’ll only know your best effort if you don’t give up.

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #77 on: October 12, 2018, 08:13:08 pm »

This may be a good alternative for the price and there is a model above and below optionally. Looking at the original Emax this should be a little more power. NOTE though that these are 5s LiPo max
https://hobbyking.com/en_us/turnigy-aerodrive-sk3-4250-410kv-brushless-outrunner-motor.html
Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #78 on: October 13, 2018, 02:55:37 pm »

Hoi Tamaris ..

thank you first for your help ..

The PO-5065-360 would be good because I still have 6s lipos and I could continue to use them .. but the motor shaft has a diameter of 8mm and there I find no matching clutches ..

The Turnigy Aerodrive SK3 - 4250-410KV has a little more turns and the shaft diameter of 5mm is suitable for me because I still have matching couplings. However, I would need for him new batteries ..

but the more I think about it I'll probably decide for the Turnigy. .hab still a little time until I need it ..

as a controller, I have chosen this one here. .I think he fits very well ..


https://hobbyking.com/de_de/hobbyking-70a-boat-esc-4a-ubec.html
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #79 on: October 13, 2018, 04:14:44 pm »

Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #80 on: October 13, 2018, 05:19:21 pm »

a great video .. !!

as a battery I would take this then ..



https://hobbyking.com/de_de/turnigy-battery-5000mah-5s-25c-lipo-pack-xt-90.html
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #81 on: October 13, 2018, 05:25:29 pm »


Thank you

Good price  :-))
Logged
ANDY
You’ll only know your best effort if you don’t give up.

typhoon

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 30
Re: TAMAR Speedline 1/12
« Reply #82 on: October 19, 2018, 06:12:20 pm »

Possible?
I have 6 of these
https://hobbyking.com/en_us/turnigy-5000mah-4s1p-14-8v-20c-hardcase-pack-1.html

20 -30 minutes with 2x 1185kv
https://youtu.be/Pg4sldNNFRY


sorry but  that seems ridiculously well  over the scale speed !
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #83 on: October 19, 2018, 06:46:15 pm »

No need to be sorry you are correct  :-))
Easy to turn it down but you can’t turn it up  {-)

Logged
ANDY
You’ll only know your best effort if you don’t give up.

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #84 on: October 19, 2018, 08:20:21 pm »


sorry but  that seems ridiculously well  over the scale speed !
That was a testing session in the worst conditions I’ve had the opportunity to make use of .
I discovered that strong wind seriously affects steering due to the bow being almost completely out of the water. I proved it won’t blow 25 amp fuses at continuous full speed
She’ll turn hard with no instability and is now completely reliable.
My silicon seal for the deck limits water ingress and bilge pump sorts the rest.
I need a smaller body if water with same wind for tougher waves
At more sedate speeds and manoeuvring I can get nearer 45mins running


Here just for you  :-)
https://photos.smugmug.com/photos/i-2S8HzhZ/0/b8a9da85/1920/i-2S8HzhZ-1920.mp4
Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #85 on: November 11, 2018, 08:40:05 am »

Hoi Taranis ..


You have 6 of 5000mAh batteries .. ?? did you connect them in parallel to increase the capacity and so the travel time .. ??


Holger
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #86 on: November 11, 2018, 08:57:28 am »

No they are used one pair at a time for three sailings


Logged
ANDY
You’ll only know your best effort if you don’t give up.

gingyer

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,684
  • Location: Glasgow
Re: TAMAR Speedline 1/12
« Reply #87 on: November 11, 2018, 03:07:21 pm »

Is that 20minutes for a pair of batteries or all 6??
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #88 on: November 11, 2018, 04:09:22 pm »

Per pair up to 45 minutes depending on speed
Logged
ANDY
You’ll only know your best effort if you don’t give up.

gingyer

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,684
  • Location: Glasgow
Re: TAMAR Speedline 1/12
« Reply #89 on: November 12, 2018, 09:19:43 am »

thanks, I was wondering when I read it  :-))
Logged

Flundle (Speedline Models)

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 206
Re: TAMAR Speedline 1/12
« Reply #90 on: November 28, 2018, 05:21:17 pm »

For the Tamar, Turnigy Aerodrive SK3 - 4250-410KV Brushless Outrunner Motors are ideal and cheaper too!
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #91 on: November 28, 2018, 09:34:56 pm »

This may be a good alternative for the price and there is a model above and below optionally. Looking at the original Emax this should be a little more power. NOTE though that these are 5s LiPo max
https://hobbyking.com/en_us/turnigy-aerodrive-sk3-4250-410kv-brushless-outrunner-motor.html
I spent a whole evening researching to establish that  {-)
Unfortunately now the Uk price is ridiculously low because there is no stock
The EU warehouse does of course have stock at twice the price  <*< thank you hobby king for nothing
Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #92 on: November 29, 2018, 03:03:55 pm »

that's the heart of my Tamar ..
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #93 on: November 29, 2018, 09:03:51 pm »

 :-))  You bought back at the right time. Stocks of everything are now almost completely exhausted until further notice

Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #94 on: December 23, 2018, 08:53:26 am »

Hoi Olav ..

on the first picture on page 3, the position of the two water inlets is clearly visible .. a precise measure to the back you can see yes .. but unfortunately you see the other that does not go forward .. can you please send me this measure or a picture of it .. ??

Thanks a lot, says Holger
Logged

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #95 on: December 30, 2018, 05:55:32 pm »

hoi Kim ..

I'm just about to do all the drilling and sawing for all internals of motors .. pumps .. on page 3 in the first picture are also the two water inlets to see .. but only with the measure to the keel .. the second measure is not More to see on the picture .. and exactly this measure I need now urgently for the exact position of the inlets ..

if you do not do a very big effort you could please nachschuen on the plan after the measure .. ??

Thank you, Holger says
Logged

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #96 on: April 22, 2019, 07:37:32 am »

Hi
Now I have both controllers - Turnigy Marine ESC 90A - programmed and if I plug them individually at the receiver you run .. because I want to run both motors s.einer receiver channel I have heaped on a regulator + cable and with a Y-cable with connected to the receiver .. now but only the engine runs with the three cables and where I pulled out the + cable beeps only as not yet programmed ..

what is not working .. ??

how did you connect the regulators .. ??
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,300
  • Balne Moor MBC
  • Location: Yorkshire
Re: TAMAR Speedline 1/12
« Reply #97 on: April 22, 2019, 08:01:06 am »

With mine I think throttle has to be at full when transmitter is turned on before switching on receiver
Then I get confirmation beeps from both ESC at which point pull throttle back to null.


Is it a plain Y cable ? Not one with servo reverser on one leg
Logged
ANDY
You’ll only know your best effort if you don’t give up.

Holger

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 64
  • Model Boat Mayhem is Great!
  • Location: Riesa
Re: TAMAR Speedline 1/12
« Reply #98 on: April 22, 2019, 11:14:05 am »

yes Andy .. it's a simple Y-cable ..

I have also inquired on Facebook and as one uses the same controller without a red cable to remove and it works perfectly with him ..

So I would only once again see if both motors individually again run and if so both then connect with the Y-cable and hope then both run as planned ..
Logged

JimG

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,268
  • Model Boat Mayhem is Great!
  • Location: Dundee
Re: TAMAR Speedline 1/12
« Reply #99 on: April 22, 2019, 12:49:15 pm »

Are you sure that the receiver is powered up? An esc which is not receiving a signal will beep to let you know this. Make sure the receiver is powered up first before connecting power to the esc.
Jim
Logged
Dundee Model Boat club
Pages: 1 2 3 [4] 5   Go Up
 

Page created in 0.105 seconds with 21 queries.