Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Can anyone help? - drill out and tap these pulleys  (Read 2132 times)

F4TCT

  • I am not completely useless.......I can always serve as a BAD example
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 536
  • Location: Whitby, North Yorkshire, UK
    • My Boat Builds
Can anyone help? - drill out and tap these pulleys
« on: February 26, 2016, 06:03:51 pm »

Hi chaps, I was wondering if anyone with some decent machining gear could possibly drill out and tap these pulleys to m5 x 0.8 thread for me?


The bore is currently 3mm and while I can manage the hold the pulley against the drills torque without any slippage, I just can't drill straight enough by hand. I need a pillar drill and one is on the cards but I need to sort my workshop space out first.





The pulleys are from motionco and if anyone can help then there's some beer money in it :) Im down to my last pair and I'd rather not ruin these.
















Dan
Logged

Crossie

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 234
  • Model Boat Mayhem is Great!
  • Location: Norfolk UK
Re: Can anyone help?
« Reply #1 on: February 26, 2016, 06:27:46 pm »


Hi Dan,
                           pm sent,
                                                     Trevor
Logged

sparkey

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,211
  • I think I am as mad as I think I am then I am mad
  • Location: wandsworth
Re: Can anyone help? - drill out and tap these pulleys
« Reply #2 on: February 27, 2016, 09:56:58 am »

 :-)) If you don't get a result,I will do for you on the lathe mate,please let me know either way...........Ray :-)) 
Logged
My boats are all wood like my head fluctuat nec mergitur

Captain fizz

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 275
  • Model Boat Mayhem is Great!
  • Location: Oakham Rutland
Re: Can anyone help? - drill out and tap these pulleys
« Reply #3 on: February 27, 2016, 10:22:01 am »

This is what is great about this site, instant offers of help.
Well done all. :-))
Logged

mrturbo553

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 154
  • Location: Goole or Scarborough
    • North Sea winches
Re: Can anyone help? - drill out and tap these pulleys
« Reply #4 on: February 27, 2016, 11:30:34 am »

Dan , if you haven't already managed to get these done , drop me a pm
Cheers Aid
Btw they look very similar to the mfa belt pulley's
Logged
Gone racing back in 9.5 sec
http://www.nswinches.co.uk

F4TCT

  • I am not completely useless.......I can always serve as a BAD example
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 536
  • Location: Whitby, North Yorkshire, UK
    • My Boat Builds
Re: Can anyone help? - drill out and tap these pulleys
« Reply #5 on: February 27, 2016, 01:12:29 pm »

Don't all fight over me :)


I'll send them off to Trevor today.


Thanks for your offers.


Dan
Logged
Pages: [1]   Go Up
 

Page created in 0.102 seconds with 21 queries.