Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: 1 ... 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 [38]   Go Down

Author Topic: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build  (Read 273381 times)

Macsmouldings

  • Martin
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 162
  • Supplier of Larger Scale Modelling Accessories
  • Location: Sheerness, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #925 on: March 22, 2020, 06:37:01 pm »

Evening Kim, Looks really good fella, keep up the good work and stay well, talk soon fella

Regards,

Martin.
Logged
Supplier of Larger Scale Modelling Accessories

Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #926 on: March 22, 2020, 11:15:28 pm »

Thanks Martin, good to hear from you......will be in touch in the next couple of days.


So, this afternoon I made the second hinge and tidied up the first one. Tomorrow will have a look to see which bolts to use for the hinges and fix [temporary of course, as these will all need to come off at various stages and also a hand rail will need to be attached]. The first photo shows the second hinge in a 'dry fit' and then the progression. Used the Proxxon belt sander for this - bit OTT, however, one gets used to the balance problem after a while with such small items.....but it worked.


After this I might then make a few detailed smaller items for a change.


C.C.
Logged

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,981
  • Kirklees MBC/ Balne Moor MBC
  • Location: Yorkshire
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #927 on: March 24, 2020, 12:29:28 pm »

Nice job Kim
You likely noticed I used that grab rail as a means to fix it all in place without glue until after final painting.
I'm producing nothing of late due to shingles being quite a distraction.
I'm looking forwards to your smaller items  :-)


Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #928 on: March 25, 2020, 03:16:46 pm »

Thanks Andy, sorry to hear of your ailment and hope your are fully back to sound health and comfort very quickly.


Yes, like you, I had realised some time back that these pieces [with their very tight fit] will need special attention. Mine has a 1.2mm thread in both ends of the handrail and this will act like a captivated bolt, hence fitted from the other side to pull it into place. The holes just have to be drilled..........
......however, with the Covid 19 situation, the gardener I had just employed to do my 'small patches' has to remain at home. Thankfully he had given the front and back gardens a high and medium cut last week [first cut after the winter - ha, ha], so the biggest job done. I will now have to keep this going until matters return to 'normal'. I cut both yesterday [it's like summer down here] and attempted a little edging and pruning, but my hip and back gave up!! So, time for modelling very slightly reduced, just after I had started to make progress. That's life though. A few thoughts later tonight though.


Take care, Kim
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #929 on: April 19, 2020, 06:32:18 pm »

I have built some rails during the last few weeks. The upright of the pulpit rail is a brass tube which contains the leads for the LED. I used 3mm LEDs which fit into the tube after some sanding. The rounded cap was sanded flat and then polished.
The gate is only a trial fit, the bottom hinge will be correct in the final fixing. The hinges are fixed using M1.2 hex bolts (same for the backside plate). I chose M1 bolts for the plate which accepts the locking pin. The bolts, washers and nuts were bought from Prime Miniatures (UK).

The rails at the roof were silver soldered. I chose soft soldering for the other parts and soldered them in situ. The gate is a mix of silver and soft soldering. The insert was glued in using epoxy glue. Should other Shannon builders be interested, Kim might supply some gate inserts. He has a few of them left which could be completed with the laser cut lettering from a German jeweller (might need some time  but we still keep the data files, so should be no problem).

Bending the brass rod was easier than I had expected it to be. I used my Robbe bending tool, a vice for the 90 degrees angles and  pliers for the areas where only a slight bend was needed.


Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #930 on: June 22, 2020, 04:52:50 pm »

Kim kindly permitted me to post some photos of my radar scanner before he will get back on his Shannon build in about two weeks time.
I used the original Furuno plans provided on Kim's DVD, zoomed them to the appropriate size on my printer and cut them out as templates. I tranferred those to a box made from 4 mm styrene using a pencil. Sanding the item to the correct shape was not easy as the shape is quite complex and this took me several hours. The sides were cut from 0.5 mm styrene and fixed by cyano glue.
I wanted to get as little friction as possible and used ball bearings of 3 mm diameter (1 mm shaft) from Knupfer. Two of them were inserted into a brass tube, fixed by Loctite.
The motor is from sol-expert in Germany, it was a kit of its own with this tiny gearbox, great fun to assemble and to see it working in the end! Sol-expert provide a small ESC which allows to run the system at a maximum voltage of 18 Volts, adjusting the speed to about 26 rpm as per the original.
The bolts and the ground lead will be added later.
Logged

Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #931 on: June 22, 2020, 05:08:39 pm »

Arno, that's a superb bit of building and mechanics. I'm so glad you have added this and it will 'close the gap' time wise until I get back to my Shannon build  :-)) .
As you know, and have seen, I am having a break and currently building, preparing and painting a couple of my 1/10th scale historical figures - a Teutonic knight and Boudicca - Queen of the Iceni tribe.


Kim [C.C.]



Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #932 on: July 19, 2020, 01:29:13 pm »

As Kim is still having a break from his Shannon build, he encouraged me to post some photos of what I did in the meantime.
The stanchions were silver soldered. The eyelets will be fixed with soft solder later. I have turned the sockets from brass tube (inner diameter 3.5 mm) on my lathe and will fix them with glue onto the deck. The stanchions themselves have a very tight fit so that inserting a pin will hold them in place as per the original.
I have attached some photos of my mass production.
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #933 on: July 19, 2020, 01:49:00 pm »

I built the navigation lights from a clear 8mm Plexiglas rod (I think in the UK you call it Perspex). I fixed a piece of the rod in the chuck of my lathe and milled the hole using a 4 mm endmill in the tailstock. In order to achieve the rounded shape I used a hand file at very low revs. Then I used some sanding paper, beginning with a 240 grit followed by finer grits. You have to cut the piece from the rod also at very low revs otherwise it will kink. Then I polished the item with metal polish (toothpaste should do the job as well). I have also polished the inside so that it looks clear as glass again.

I will paint the lights using Tamiya clear red and green and black for the housing with a brush. Later red and green SMD leds will be used for illuminating.
The blue beacon light is from Pistenking in Germany. It has 12 SMD leds in blue which replicate the revolving effect very realistically. I have painted the cap using Tamiya clear blue with a brush.
We are not sure whether the orange light should be revolving or light in a flashing mode. Kim will check this after the pandemic at the Dungeness lifeboat station. Meanwhile we think it should have a flashing mode. I have used a Chinese light bought from e..y and modified this (sanded the housing down and milled the inside so that it will accept the electronics of 5 leds again) It can be programmed either in a revolving or a flashing mode so that can be adjusted later. I have painted it using Tamiya clear orange as this is more glossy than the bought item.
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #934 on: July 19, 2020, 01:53:57 pm »

Finally, I have made a start on the Bosch camera using a 12 mm pearl which has been flattened on the sides and the front where the lens is situated. The shield was made from Tamiya 0.2 mm plasticard. I will have to replicate the wiper though probably using some styrene profiles. On the photo I have attached the different parts with masking tape only to show what it will look like later.
Logged

Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #935 on: July 20, 2020, 10:40:24 am »

Wow Arno!! Those stanchions and their 'deck feet' are superb and all the lighting is progressing so well too. Then the Bosch video camera. Who said scratch building was dead??
Thanks for keeping the interest here going.....just wished I could have visited Germany and seen you a few months back. C'est la vie! [as they say in France!].
I had a Zoom Meeting with my Military Modelling Group last Saturday and it was so good to be able to show them my small progress on the 'figures' and 1/48th jets side too. I will get back to the Shannon soonish, but with no Shows on the horizon and other matters, it gives me a chance to do something different..............
Keep it going though and thanks for the Post.
Kim
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #936 on: October 15, 2020, 06:45:56 pm »

As Kim's build is still on hold he encouraged me to post some of my latest progress of my Shannon build. The stanchions were silver soldered, the fittings for the shackles soft soldered. The shackles are from Knupfer (they are the casting ones, not the brass rod items). The sockets were turned on my lathe.
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #937 on: October 15, 2020, 06:58:56 pm »

The foot switch for the capstan was a lovely small item which came out pretty well. I turned the'washers' from aluminium, drilling a hole of 4mm diameter first. Then I machined them down to 14 and 10 mm outer diameter. I then fixed each of them using a screw as a shaft in the rotary table of my milling machine and drilled the 0.6 mm holes, adjusting the start with my laser point edge finder. You can see the tiny tap (M 0. 8) I used for tapping (Swiss made and bought from Knupfer as well). The screws are M 0.8 mm stainless steel and were fixed with the Horotec screwdriver. Mind that you have to bring the slots of the screws all in a circular position (now this is rivet counting, isn't it :-)) ) if you want it to look like the original item on the Dungeness boat! The rubber cover of the switch was replicated using a 4 mm pearl which my daughter gave me (flattened the top and painted using Revell black semi matte, thanks Anke ok2 ).
Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #938 on: October 15, 2020, 07:11:43 pm »

First I intended to use Tamiya black cable for the railings but could not really get that to a straight line. So I decided to take carbon tubing instead (supplied by R&G Faserverbundwerkstoffe, Germany, you can see the item no. on the photo). The turnbuckles are from prime miniatures (UK), flattened the middle section in order to get closer to the real items. The fittings are made from 3 mm aluminium rod, drilled the hole of 1 mm diameter, then fixed in the key chuck of my Foredom motor drill and sanded down. The opposite side was shaped using a hand file (you have to make 36 pieces of that, real mass production %% ). I will use the Tamiya cable only for connecting the first stanchion to the pulpit rail.
I hope you like the teaser and Kim will be able to continue his build soon O0
Logged

Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #940 on: October 16, 2020, 03:46:42 pm »

Arno,
Very many thanks, bro'. The stanchions look wonderful and you have certainly made a good job of the silver soldering. Likewise the detail on them is superb. However, that deck foot-switch for the capstan is a little 'gem' [actually that's a pun in the circumstances!! Good 'old' Anke!]. Your approach to the turnbuckles is a good approach too [I have similar on my Arun and Trent class models also] and these will help a number of fellow builders, especially as you have put the techniques and traders' details there too.


I can tell you are enjoying it, so maybe I will have to get back to mine soon.


As you know I sent off 210 to RNLI Dungeness recently from my DVD monies and a speaking engagement fee. Since then I have had two more requests for various DVDs of my photos and both gents were very generous and I now have another 55 which I will send when a bit more has accrued. These are very difficult days for the RNLI's funds, as the Stations and their shops are closed, due to Covid, and these bring in a vast amount, alongside the Open Days each year. So thanks to all of you over the years that have purchased the DVDs. Over 1,000 has been raised in the past twenty years from them.


I shall return........


Kim [C.C.]



Logged

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 98
  • Location: Germany
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #941 on: November 15, 2020, 07:07:36 pm »

I have been working on the survivor's gantry and the lights at the top of the wheelhouse. In order to keep it lightweight, I have used carbon tubes for the gantry. The item is moveable like the real thing and can be hold in position fixing the small arm at the hook at the side of the wheelhouse. I was not sure if the mix of materials would result in a rigid item, but it is indeed. I have used epoxy glue for the tubes.
The lights are made from acrylic pearls. I fixed them in the rotary table of my milling machine and using endmills for aluminium  (those are much sharrper at the edges than those used for steel) lead to a crisp result. As the pearls had holes for putting them on a thread, I had to close them with car body filler. The ring will carry the lens and then be glued to the body of the pearl.

The smd led's have three chips in one part. I decided to solder all three of them in parallel and they are very bright indeed. The lights can be adjusted as they are fixed with a hex bolt to their brass holders.
Logged

Canterbury Coxswain

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 751
  • Is there anything other than lifeboats and yachts?
  • Location: Canterbury, Kent
Re: Shannon 'RNLB The Morrell' 13-02 [Models by Design] - a 1/12th build
« Reply #942 on: November 16, 2020, 02:27:18 am »

Arno, that gantry is absolutely magic. So glad it is all going well bro',  :-))
Kim


Logged
Pages: 1 ... 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 [38]   Go Up