Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 [14]   Go Down

Author Topic: Panart/Mantua Anteo Steam Tug Build  (Read 38151 times)

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #325 on: January 05, 2020, 09:46:51 AM »

Hi John thanks for the comments.  I had completely overlooked the thought of being able to see the water pressure gauge.  I can see it clearly without the superstructure being on but its something I will need to think about so thanks for that  :-))   Fortunately though the gas tank is removable and thats what I intend to do when it requires filling and also I can get quite a lot of ballast actually underneath the boiler/motor plate.  If I cant get enough there I'll probably fix it outside in the keel but here's hoping
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,651
  • Kirklees MBC/ Balne Moor MBC
  • Location: Yorkshire
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #326 on: January 05, 2020, 09:53:34 AM »

Hi Mark.
Lead shot from a gunshop is incredibly heavy if expensive but can poor into shapes and add resin to bind it. Using with clingfilm or similar to prevent it sticking to the hull. If it then turns out to be over weight you can pull it out and cut some off. Alternatively just us individual bags and it still fits better than blocks of lead
Logged
ANDY
Lobster boat
Portgarth
Every day above ground is a good one

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #327 on: January 05, 2020, 09:56:46 AM »

Hi Mark.
Lead shot from a gunshop is incredibly heavy if expensive but can poor into shapes and add resin to bind it. Using with clingfilm or similar to prevent it sticking to the hull. If it then turns out to be over weight you can pull it out and cut some off


Hi Andy  - yep this is what I used on my last build and it worked great.  I like the way it moulds to the hull and doesn't move when underway  :-))
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,651
  • Kirklees MBC/ Balne Moor MBC
  • Location: Yorkshire
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #328 on: January 05, 2020, 09:57:56 AM »

It may be you I got the idea from then  {-)   :-))
Logged
ANDY
Lobster boat
Portgarth
Every day above ground is a good one

Jerry C

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,117
  • Location: Caernarfon, North Wales.
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #329 on: January 05, 2020, 10:15:17 AM »

I wouldn’t worry about removing the gas tank each time to fill it. I don’t.  If there’s a bit of gas lying around it just goes pop when you light the burner. You’ll have the tophamper off for filling anyway, keeps your eyebrows short!
Jerry.

southsteyne2

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 273
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #330 on: January 05, 2020, 12:40:39 PM »

One needs a good sturdy bag for the lead shot nothing worse than the little black buggers rolling around in the hull and difficult to remove,
Cheers
John
Logged

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #331 on: January 05, 2020, 01:46:04 PM »

Hi John on my last build I found the places that I wanted to place the lead shot and then placed cling film into that area.  I then poured the lead shot onto the cling film and pulled it around to make a bag.  Next I poured epoxy resin into the bag of shot and then pushed the bag exactly into place.  Once the epoxy had hardened the shot was like a solid block and was going no where.  It was like a solid piece of lead that fitted exactly into the hull but was also removable because the cling film stopped it from sticking to the hull.  It is possible to remove the cling film but I've just left mine on.
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

rhavrane

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 491
  • Steam passionate collector
  • Location: Saint-Mandé, Val-de-Marne, France
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #332 on: January 05, 2020, 05:23:57 PM »

Bonjour,
In France, we can find 2mm thick sheets of lead. I cut it with scissors to put in in the frame without any glue because, I have to finish the boat and remove some weight, nothing moves : https://www.youtube.com/watch?v=Y6q4yYpVcA8
Logged
Raphaël
Raphaëlopoulos Steam Lines UnLimited
Membre du Modele Yacht Club de Paris http://mycparis.fr/
Ma chaîne YouTube:  http://www.youtube.com/user/rhavrane
Mes albums : https://picasaweb.google.com/104408627118165995713/

KNO3

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,215
  • Location: Vienna
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #333 on: January 19, 2020, 06:55:40 PM »

I
Bonjour,
In France, we can find 2mm thick sheets of lead. I cut it with scissors to put in in the frame without any glue because, I have to finish the boat and remove some weight, nothing moves : https://www.youtube.com/watch?v=Y6q4yYpVcA8


I use lead sheet for ballast too, it is very good as it is easy to cut and  fit on the bottom of the hull even under the steam plant and other tight spots.
Logged

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #334 on: January 26, 2020, 09:38:55 AM »

Sorry about the lack of updates on this build but I've had a bit of a set back.


I was using some 20 minute epoxy resin on the inside to fill up some of the weaker parts of the hull.  I did this on my last build and it worked well.  Unfortunately I poured a bit to much in one area and wow - the heat build up was so hot that I couldn't even touch the hull with my bare fingers.  I cooled it all down using wet cloths on the outside for about 30 minutes which worked well.


The good news was that the wood work did not move one bit under such heat so the planking has proven to be solid.  The bad news was that it blistered the epoxy finish on the outside of the hull in a few small places.  It really did look bad but after a few days of sanding back and repair work its all looking good again.


Such a silly mistake by me that has caused days of work.  Anyway I'm now back to where I was weeks ago so hopefully I'll have something more positive soon


Mark
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

Capt Podge

  • Full Mayhemer
  • *****
  • Online Online
  • Posts: 3,403
  • Location: Blyth, Northumberland
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #335 on: January 26, 2020, 10:08:52 AM »

That was a swift rescue with the wet cloths Mark, you definitely avoided a total disaster there.


Hopefully, that will be your last setback on this build  :-)


Regards,
Ray.
Logged
Pop top campervan needed

southsteyne2

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 273
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #336 on: January 26, 2020, 12:37:16 PM »

Very lucky Mark its called exotherm we used to have lots of problems in telephone cable joints as it would melt the tiny plastic insulation.
 I updated my Joffre build post but so far no replies oh well tugs and towing.
Cheers
John
Logged

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #337 on: January 26, 2020, 02:54:37 PM »

Lads I was lucky - if this had been a plastic or resin hull it would have definitely ruined the complete thing.  I knew that epoxy could get warm but I never realised it could get as hot as it did.  I think its important to put our errors on our build logs so that others can see that nothing quite goes to plan  {-)


I can now get on with getting the inside of the hull coated as I've finished sanding it out which quite frankly is a thankless task.  Oh and I need to get the prop tube glued in too.
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #338 on: March 02, 2020, 05:49:18 PM »

Hi All


A bit of an update on this build


Firstly I gave the hull a good couple of coats of epoxy on the inside to protect it and give it some strength too.  I really dislike this job for some reason and I put it off for weeks.  Then I fitted the studs for the motor and boiler mount which go all of the way through the frames.








I then epoxied in the studs that will hold the servo for the gas valve as it will be impossible to fit them at a later stage





And then fitted the stainless steel servo mounts as I think it will be easier to do it now rather than later.  Sorry about the picture being the wrong way around.





Then the propshaft was epoxied into place and you can see how the oiler tube just fits around the separator mount





Next was to fit the deck beams in place which then had their first coat of resin








And so did the sub deck





The deck and the beams were then sanded and given a second coat of resin.  Whilst this was still wet the whole assembly was put together and screwed down using very small stainless steel screws








Once it was all dry the bulwark supports were removed











Next I did an experiment to see how to make the caulking in-between the decks.  I used an archival ink pen and you can see the results.  Side 1 is colouring only one side of each plank and side 2 is colouring both sides of each plank.  I really couldn't see much in it so I have decided to colour both sides.  I also gave them a coat of varnish just to make sure that the ink did not run.











So the next job is the planking of the deck.  I really like the colour of the sub deck so I have decided to use pear wood for the deck as its pretty much the same colour.  I spent a couple of hours on the table saw and made some 1mm x 6mm planks which should look very nice once they are glued on








So all in all things are going to plan albeit at my usual slow pace.  I should have the deck done this weekend  - well hopefully


Thanks for looking - Mark
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html

Taranis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 2,651
  • Kirklees MBC/ Balne Moor MBC
  • Location: Yorkshire
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #339 on: March 02, 2020, 06:12:13 PM »

Quite amazing  8)
Logged
ANDY
Lobster boat
Portgarth
Every day above ground is a good one

Capt Podge

  • Full Mayhemer
  • *****
  • Online Online
  • Posts: 3,403
  • Location: Blyth, Northumberland
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #340 on: March 02, 2020, 06:22:41 PM »

Thoughtful, practical and inspirational application - great to see and follow - keep it going Mark.  :-)
Logged
Pop top campervan needed

Jerry C

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,117
  • Location: Caernarfon, North Wales.
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #341 on: March 03, 2020, 03:08:35 AM »

BOSTIN!
Jerry.

Mark T

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,091
  • Location: Dudley in the Black Country
Re: Panart/Mantua Anteo Steam Tug Build
« Reply #342 on: March 03, 2020, 12:56:10 PM »

Thanks all  :-))   The decking is going on really well so it shouldn’t take too long to do. Then I’ll need to fit the forecastle deck and plank that too. Then the bulwarks get another layer on the inside just to finish them off. Loads to do but enjoyable  :-)
Logged
Its not the finishing that matters - Its the journey along the way that counts

Fairmount Alpine Build http://modelboatmayhemimages.co.uk/album/bXv
Anteo Tug Build http://www.modelboatmayhem.co.uk/forum/index.php/topic,59708.0.html
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 [14]   Go Up