Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Variable rotary switch supplier?  (Read 1870 times)

justboatonic

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,516
  • Location: Thornton Cleveleys
Variable rotary switch supplier?
« on: January 21, 2018, 05:23:53 pm »

Sorry, couldnt find anywhere else suitable for this question.

OK, leds with resistors in line, wire a number up inside the superstructure and a couple on outside bulkheads etc. I then want to be able to vary the brightness of these leds via a rotary switch. The leds will run off a 12v supply but I want to be able to vary the voltage and hence brightness in the range of about 3v to around 9v. Yes, I could just use a toggle switch to change the supply voltage between the two but would like a bit more control to eye ball the brightness to just the right level for the daylight conditions.

Anyone know what type of rotary switch I need to search for and where to buy? TIA.
Logged

bfgstew

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 502
  • Comfortably Numb
  • Location: Retford (Robin Hood Country)
Re: Variable rotary switch supplier?
« Reply #1 on: January 21, 2018, 05:47:29 pm »

I use these for most of my components.


https://www.bitsbox.co.uk.....hope it helps.
Logged
"Give me a ping Vasili. One ping only, please"

roycv

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,389
  • Location: S.W. Herts
Re: Variable rotary switch supplier?
« Reply #2 on: January 21, 2018, 06:07:23 pm »

Hi have you tried using an ESC to see if that works?  If it does you can buy a cheap forwards only one for a few quid on ebay.  I am assuming you want to do it by remote control.
regards Roy
Logged

inertia

  • Guest
Re: Variable rotary switch supplier?
« Reply #3 on: January 21, 2018, 06:47:26 pm »

Use a voltage reducer. Plenty here https://www.componentshop.co.uk/power-supplies.html
DM
Logged

canabus

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,347
  • Boats a hole in the water you pour money into!!!
  • Location: Tasmania,Australia
Re: Variable rotary switch supplier?
« Reply #4 on: January 22, 2018, 06:01:52 am »

Banggood Frsky Taranis X9E 6  position switch part No. 1043146.
I removed the circuit board to change a vari pot into a 6 switch setup.
Note the first position is normal on, so I got a 5 position switch setup on my Turnigy/ Flysky I6 transmitter.
1 Wheelhouse lights.
2 Forward cabin lights.
3 Aft cabin lights.
4 Nav ,mast and stern lights.
5 Searchlight.

Canabus
Logged

roycv

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,389
  • Location: S.W. Herts
Re: Variable rotary switch supplier?
« Reply #5 on: January 22, 2018, 06:20:28 am »

Hi Canabus, very interesting but I think according to the thread that what was wanted was a way of varying the brightness of the leds.
regards Roy
Logged

McGherkin

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 378
  • Location: Plymouth
Re: Variable rotary switch supplier?
« Reply #6 on: January 22, 2018, 06:41:10 am »

Essentially you’re after a potentiometer? Most electrical suppliers will sell them, you just need to work out the resistance required
Logged

malcolmfrary

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 6,027
  • Location: Blackpool, Lancs, UK
Re: Variable rotary switch supplier?
« Reply #7 on: January 22, 2018, 08:46:09 am »

Essentially you’re after a potentiometer? Most electrical suppliers will sell them, you just need to work out the resistance required
LEDs need around 20mA.  This will fry the track on most pots. 
To reduce the brightness you need to reduce the current.  Two ways to this, either keep the same voltage but introduce more resistance, or keep the same resistance, but reduce the supply voltage.
A forward only ESC will combine both, can be worked from a spare channel or a servo tester.
Rotary switches (used to be called Yaxley Switches way back) could be got in various combinations of 12 - 3 pole 4 position, 4 pole 3 position etc.  Not having needed one for years, I would need to look again.  But a cheap Forward only ESC plus maybe a servo tester is probably the simplest and cheapest way to do it.  Might need a voltage dropper to supply off the 12 volts, though, depending on the ESC.
Logged
"With the right tool, you can break anything" - Garfield

chas

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 587
  • now in los montesinos Spain.
Re: Variable rotary switch supplier?
« Reply #8 on: January 22, 2018, 02:48:30 pm »

I use an old wire wound potentiometer,  if memory serves me it's only a few ohms. It has been working well for years.
Chas

Logged
Pages: [1]   Go Up
 

Page created in 0.113 seconds with 22 queries.