Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1] 2   Go Down

Author Topic: MFA large motor?  (Read 5633 times)

Rob47

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,044
  • Model Boat Mayhem is Great!
  • Location: Gloucester
MFA large motor?
« on: December 15, 2018, 09:33:48 pm »

Does anyone recall the above? I had two years ago looking for one now
They resemble fan motors all black body, about 3” dis and same for length. Three hole mounting plate. Last ones I bought cost around £20


Cheers


Bob
Logged
I will finish this model

tugmad

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 535
  • Location: Gravesend Kent
Re: MFA large motor?
« Reply #1 on: December 15, 2018, 10:02:17 pm »

That would be a Smiths fan motor, they made them with a 1/4” or a 5/16th” shaft.
Logged

derekwarner

  • Full Mayhemer
  • *****
  • Online Online
  • Posts: 9,464
  • Location: Wollongong Australia
Re: MFA large motor?
« Reply #2 on: December 15, 2018, 10:24:50 pm »

Yes Rob.....obviously an automotive heater/cooler dash type fan motor.......constant rating ...silent & super low current draw


In these days of OH&S...most Auto wreckers don't allow customers self removal....so the $ has increased ......




Derek
Logged
Derek Warner

Honorary Secretary [Retired]
Illawarra Live Steamers Co-op
Australia
www.ils.org.au

tony52

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 218
  • Location: Bury, Lancashire.
Re: MFA large motor?
« Reply #3 on: December 15, 2018, 10:39:08 pm »

MFA Barracuda 12-24v. Used one to power my 46" Crash Tender after removing the i.c. power plant.

Tony
Logged

Rob47

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,044
  • Model Boat Mayhem is Great!
  • Location: Gloucester
Re: MFA large motor?
« Reply #4 on: December 16, 2018, 04:32:27 pm »


Tony not barracuda, to small and wrong shape

Logged
I will finish this model

Rob47

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,044
  • Model Boat Mayhem is Great!
  • Location: Gloucester
Re: MFA large motor?
« Reply #5 on: December 16, 2018, 04:48:33 pm »

Logged
I will finish this model

gingyer

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,684
  • Location: Glasgow
Re: MFA large motor?
« Reply #6 on: December 16, 2018, 05:11:37 pm »

24v smiths fan motor
Logged

Treble

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 39
  • Model Boat Mayhem is Great!
  • Location: Barnsley , South Yorkshire
Re: MFA large motor?
« Reply #7 on: December 16, 2018, 05:15:46 pm »

Bob , Sure I have a couple in stock . Will check and let you know . If I do have them will take pics and either post ( never done it so don't know how ) , or email you . Trevor .
Logged

unbuiltnautilus

  • Portsmouth Model Boat Display Team
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,154
  • Location: Portsmouth, England, third rock from the Sun....
Re: MFA large motor?
« Reply #8 on: December 16, 2018, 05:25:08 pm »

MFA Barracuda 12-24v. Used one to power my 46" Crash Tender after removing the i.c. power plant.

Tony


I tend to agree. We are going back before MFA Torpedo motors and Marlins, probably twenty years ago, but I think it was a Barracuda.

Logged
Listen politely, nod approvingly, then do what you want, works for me!

Rob47

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,044
  • Model Boat Mayhem is Great!
  • Location: Gloucester
Re: MFA large motor?
« Reply #9 on: December 16, 2018, 07:11:52 pm »

Bob , Sure I have a couple in stock . Will check and let you know . If I do have them will take pics and either post ( never done it so don't know how ) , or email you . Trevor .



Cheers
Bob
Logged
I will finish this model

Treble

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 39
  • Model Boat Mayhem is Great!
  • Location: Barnsley , South Yorkshire
Re: MFA large motor?
« Reply #10 on: December 31, 2018, 12:56:02 pm »

Bob , Have checked stocks ans found I have 1 black motor 74mm dia x90mm long wi 6 mm dia shaft and 3 silver ones 76 mm dia x 95 mm long wi 8 mm dia shft . Have taken pic , so if you could let me know your email address, I will send it to you . Trevor  . 
Logged

morley bill 1

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 300
  • Model Boat Mayhem is Great!
  • Location: east yorkshire coast
Re: MFA large motor?
« Reply #11 on: December 31, 2018, 03:43:03 pm »

Hi I always knew the as barracuda motors powered a large tug with one over 30 years ago brilliant motors  Bill...
Logged

Dave_S.

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 488
  • Member of Oxford Model Boat Club
  • Location: between Oxford and Witney
Re: MFA large motor?
« Reply #12 on: December 31, 2018, 07:18:03 pm »

I had a Veron Fast Patrol Boat powered by a Barracuda and a couple of 12v SLAs 25 or more years ago, looked good on the water.
Logged
Ruining perfectly good kits since 1969.

phillnjack3

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 112
  • Model Boat Mayhem is Great!
  • Location: slough berks. England
Re: MFA large motor?
« Reply #13 on: May 11, 2021, 12:37:36 am »

Just been messing about getting one of my boats out and then see this pop up.
My boat has a MFA Barracuda and just trying to work out best battery for it

Logged

mudway

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 507
  • Model Boat Mayhem is Great
  • Location: Sydney
Re: MFA large motor?
« Reply #14 on: May 11, 2021, 03:29:58 am »

Specs are attached. I still have a couple of them.
Logged

mudway

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 507
  • Model Boat Mayhem is Great
  • Location: Sydney
Re: MFA large motor?
« Reply #15 on: May 11, 2021, 03:34:19 am »

A spec sheet I received from MFA some time back.
Logged

nemesis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,074
  • Location: North Shields. Northumberland
Re: MFA large motor?
« Reply #16 on: May 11, 2021, 03:01:20 pm »

I have ran these motors for years, 3000rpm on 12 v, about an amp on the bench. I had two in my Arun running on 12 to 18 volts. An excellent motor. I also used them in my Ice breaker and the Northsider with a three to one reduction drive. nemesis
Logged

nemesis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,074
  • Location: North Shields. Northumberland
Re: MFA large motor?
« Reply #17 on: May 11, 2021, 03:05:44 pm »

Sorry I missed out the Barracuda has the little tube sticking up at one end, it has always been a speculation as to what it was for, nemesis
Logged

phillnjack3

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 112
  • Model Boat Mayhem is Great!
  • Location: slough berks. England
Re: MFA large motor?
« Reply #18 on: May 11, 2021, 03:25:54 pm »

Yes that tube is a funny thing to have on it.
what I was thinking is if this was originally a wiper motor in a car or heater fan motor it could been a water drain and a tube fitted to exit any water/damp out of the vehicle .
I might be miles out but cant see any other reason.. I am now about to look at it incase its for oiling a bearing ? (doubt it).
Logged

nemesis

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,074
  • Location: North Shields. Northumberland
Re: MFA large motor?
« Reply #19 on: May 11, 2021, 03:39:11 pm »

The only way to Lub the bearings is to strip the motor, give you access to the felt that surrounds the sintered bush. it is surprising just how much oil it takes. You can, if you wish, drill a little hole in the dome that carries the aft bearing. nemesis
Logged

RST

  • Guest
Re: MFA large motor?
« Reply #20 on: May 11, 2021, 03:45:19 pm »

It reminds me much of a car blower motor I had perhaps with a "Smith's" label I think. I think many years ago I got mine from mobile marine models.  Do t have it any more and not been able to find one since.  I've never thought for a minute MFA made their own motors but happy to be wrong.
Logged

RST

  • Guest
Re: MFA large motor?
« Reply #21 on: May 11, 2021, 04:31:43 pm »

Ps that "tube" might be one of the serviceable brushes the text mentions, if so that definitely fits the description of my old blower motor. Ran nice and quiet if I recall. A good chunk of ballast also -it was pretty solid.
Logged

phillnjack3

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 112
  • Model Boat Mayhem is Great!
  • Location: slough berks. England
Re: MFA large motor?
« Reply #22 on: May 11, 2021, 06:48:51 pm »

this is what is directly in line with the tube.
just took it apart to see exactly where it lines up with.
so all I can think of is it lets you see if brushes are ok ?

it does say provision for air cooling so maybe if you want to fit a hose and a small fan to blow cold air directly intothe brush area top keep cool if running hard for long periods ?
Logged

Rob47

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,044
  • Model Boat Mayhem is Great!
  • Location: Gloucester
Re: MFA large motor?
« Reply #23 on: May 11, 2021, 09:36:23 pm »

Specs are attached. I still have a couple of them.
Wow, in answer to my question all that time ago, yes that the one


Bob
Logged
I will finish this model

phillnjack3

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 112
  • Model Boat Mayhem is Great!
  • Location: slough berks. England
Re: MFA large motor?
« Reply #24 on: May 14, 2021, 02:26:54 pm »

what sort of speed controller would the mfa Barracuda motor need for 12 volt or for 24 volt operation.
im not realy into electric stuff, but have seen a load of cheap esc on ebay and wondering if these realy would do the job
I know the specs of the motor show 4 amp on load at 12 volt and 6 amp on load at 24 volt.
but when simply running this motor through a battery charger I find you realy have to put a lot on this motor to get to 4 and 6 amps.
I know boat props do like  a bit of power , the model will not be a heavy weight monster by a long way. say a max all up weight of around
14 to 18 pounds depending if I go 12 or 24 volts. I will probably just run something like x 50 to x55 prop so only about 2.5 to 3 inch pitch.
I am not after it being mega fast , just 10mph ish so its quick enough to get out and tow back in a broken down boat.

ive seen these and wondering if they would be ok or if these are gimics and I would be better off fitting the old manual type
speed controller from a 7.2 volt Tamiya car ?
I like the idea of the electric speed controller but only ever had one once and blew it up 20 odd years ago.

https://www.ebay.co.uk/itm/124260779562?epid=27004439599&hash=item1cee85062a:g:EG4AAOSwUjhfDqLo

https://www.ebay.co.uk/itm/124260779562?epid=27004439599&hash=item1cee85062a:g:EG4AAOSwUjhfDqLo

https://www.ebay.co.uk/itm/153263230580?epid=12008784758&hash=item23af334e74:g:JLEAAOSwXAxb7rD7.

if these are no good for my sort of purpose is there anything recommended on the cheap

.
Logged
Pages: [1] 2   Go Up
 

Page created in 0.194 seconds with 22 queries.