Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: Movement in servos  (Read 1986 times)

terry1956

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 180
  • Model Boat Mayhem is Great!
  • Location: yeovil
Movement in servos
« on: June 17, 2021, 11:41:57 am »

Hi chaps. Today I tried to sort out my receiver. However I am getting a lot of chatter from the other servos when I engage one servo. I have tried all sorts. I am making sure that the transmitter is turned on and the sticks etc is mid position before I switch on the receiver. But still get chatter no matter what I do. Can anyone help, thanks.
Logged

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,659
  • member of the Potteries Model boat club
Re: Movement in servos
« Reply #1 on: June 17, 2021, 11:57:44 am »

Hi Terry, how many servo,s are you using? And what operation do they do?


John
Logged

C-3PO

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,107
  • I thought that hairy beast would be the end of me
  • Location: Outer Rim world of Tatooine
Re: Movement in servos
« Reply #2 on: June 17, 2021, 12:25:28 pm »

Have you/can you try another battery to power the RX/servos - my hunch is that that may well be your problem

Regards
C-3PO


Logged
I think it's the way I have learnt most of my stuff - getting very stuck first...

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,659
  • member of the Potteries Model boat club
Re: Movement in servos
« Reply #3 on: June 17, 2021, 12:41:46 pm »

Hi Terry have you tried re-binding your Tx ?


John
Logged

terry1956

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 180
  • Model Boat Mayhem is Great!
  • Location: yeovil
Re: Movement in servos
« Reply #4 on: June 17, 2021, 01:31:22 pm »

Hi chaps. There are servos for the rudder, water pump and dive planes and one speed controller connected too the receiver. It’s a futaba f14 navy transmitter, and I am not sure binding is needed on this set up, it worked ok on another model. I will try using another battery and see if things improve. Will keep you posted.
Logged

john44

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,659
  • member of the Potteries Model boat club
Re: Movement in servos
« Reply #5 on: June 17, 2021, 03:07:28 pm »

Hi Terry,your Tx has christals, not binding buttons or switches or plugs.I would remove the christal from
the Rx give it a clean and refit see if that makes any difference if not try another Rx if you have one.
I presume your batteries are fully charged are you using a magnetic on off switch in our system?
Have you checked all switches are closing properly and you don’t have any voltage drop after them.
I repaired a friends sub recently and the main switch to the Rx had corroded so it did not switch properly.
Just ideas, hope they help


John
Logged

terry1956

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 180
  • Model Boat Mayhem is Great!
  • Location: yeovil
Re: Movement in servos
« Reply #6 on: June 17, 2021, 04:14:34 pm »

Found the fault. The chattering servo was linked to a second servo. Removed the second servo and all ok. They must of been talking to each other. Michael
Logged

malcolmfrary

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 6,027
  • Location: Blackpool, Lancs, UK
Re: Movement in servos
« Reply #7 on: June 17, 2021, 07:00:06 pm »

Found the fault. The chattering servo was linked to a second servo. Removed the second servo and all ok. They must of been talking to each other. Michael
Chattering servos is never a binding problem, and very rarely anything to do with crystals.  The symptom there is that nothing happens.
A servo on channel 1 (usually steering) on pre-2G4 sets is often interference being interpreted by the receiver as a valid, but varying, signal.
Servos misbehaving is often caused by dud power, or, in a large set-up, by an overload messing with the receiver voltage supply.  A poorly servo might puta big enough demand on that supply to cause the voltage to drop.  Since servos rely on stable voltage, they will dither in sympathy.
The servo causing this problem "might" be OK on its own, but "might" be dragging the supply voltage down.
Logged
"With the right tool, you can break anything" - Garfield

terry1956

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 180
  • Model Boat Mayhem is Great!
  • Location: yeovil
Re: Movement in servos
« Reply #8 on: June 18, 2021, 09:56:47 am »

Thanks will test the servos later for voltage drop. Good information
Logged
Pages: [1]   Go Up
 

Page created in 0.116 seconds with 22 queries.