Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: 1 [2]   Go Down

Author Topic: Graupner jet boat  (Read 6207 times)

JimG

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,398
  • Model Boat Mayhem is Great!
  • Location: Dundee
Re: Graupner jet boat
« Reply #25 on: September 01, 2021, 07:20:55 pm »
Normal styrene sheet glues well with the normal glues like Plastiweld, I also have some MEK for the more stubborn sheets. The plastic Graupner used was resistant to all I tried until I used the two part acrylic. Cyanoacrylate can be a hit or miss sometimes depending on the glue. There are some specially formulated for plastics but I prefer a welded joint using a solvent glue.
Jim
Logged
Dundee Model Boat club

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #26 on: September 03, 2021, 07:12:02 am »
Jim, I note where you are coming from, the SARS I am building is a hard plastic and the jet boat seems to be slightly softer although I made start on the wheelhouse and it went together pretty well with the cyano I use..
Logged

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #27 on: September 03, 2021, 07:13:36 am »
A few pics
Logged

Circlip

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 4,641
  • Location: North of Watford, South of Hadrians wall
Re: Graupner jet boat
« Reply #28 on: September 03, 2021, 11:32:26 am »
Have you tried Balsa Cement? Seem to remember Gropener offerings were advised to use "UHU Hart", an expensive Balsa cement.
 ABS plastics  - Acetone based adhesives, Polystyrene and PVC - Ketone based adhesives. Nylon and Polyethylene - NAILS,RIVETS and SCREWS.

   Regards  Ian.
Logged
You might not like what I say, but that doesn't mean I'm wrong.
 
What I said is not what you  think you heard.

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #29 on: September 04, 2021, 07:28:59 pm »
Not much progress on this one today as I have been spraying another boat, jet drives fitted and wheelhouse sprayed though..
Logged

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #30 on: September 05, 2021, 06:37:40 pm »
Hull sprayed today.
Logged

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #31 on: September 05, 2021, 06:39:04 pm »
Not sure why that came out upside down.
Logged

derekwarner

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 9,574
  • Location: Wollongong Australia
Re: Graupner jet boat
« Reply #32 on: September 05, 2021, 11:21:32 pm »
670russell down side up  :-))  [was the photographer standing on his head?.... or at least the pot plants face the sun 8) ]
Logged
Derek Warner

Honorary Secretary [Retired]
Illawarra Live Steamers Co-op
Australia
www.ils.org.au

6705russell

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,511
  • Model Boat Mayhem Forum is the Best!
  • Location: Staffordshire
Re: Graupner jet boat
« Reply #33 on: September 14, 2021, 08:25:45 pm »
Rest of the jet drives fitted now..
Logged
Pages: 1 [2]   Go Up
« previous next »
 

Page created in 0.017 seconds with 17 queries.