Model Boat Mayhem - Forum

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: One ESC - two motors.  (Read 2356 times)

Bradley

  • Guest
One ESC - two motors.
« on: June 21, 2008, 09:34:08 PM »

Can I run two 580 size motors through one ESC?  I don't need to control them individually - quite happy with both going ahead/both stopped/both going astern.  If this is possible, how would I wire them?  Would a 50amp ESC cope?
This sort of query may have been brought up previously but my search of the forum has not found the answers I need.
Many thanks for any help from all you knowledgeable Mayhemmers.  O0
Derek.   :police:
Logged

Arrow5

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 3,883
  • Location: Scottish Highlands
Re: One ESC - two motors.
« Reply #1 on: June 21, 2008, 09:42:20 PM »

Thanks Derek, I need to know the same but with two 540 motors and what size ESC ? :-\
Logged
..well can you land on this?

DickyD

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 9,497
  • www.srcmbc.org.uk
  • Location: Southampton UK
    • SRCMBC
Re: One ESC - two motors.
« Reply #2 on: June 21, 2008, 09:48:02 PM »

Yes you can run two motors through one escape. Wire one motor opposite way round if you have left and right props.

Shipmate 60 will tell you what esc you need, but I would think 50 amp should do.

I have two Robbe motors of a large size (no numbers on them) and i run them through a 50 amp forward 20amp reverse esc.

Though it works for me, get a second opinion on size.

For the wiring http://www.modelboatmayhem.co.uk/Common/Electrics/Images/setupsA4JPG.jpg

Diagram 1 should do.
Logged
Richard Solent Radio Controlled Model Boat Club http://www.srcmbc.org.uk

Shipmate60

  • Global Moderator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,276
  • You bark - I will bite!!!
  • Location: Fareham
Re: One ESC - two motors.
« Reply #3 on: June 21, 2008, 10:07:35 PM »

Derek, Arrow,
What voltage are you running on and what size prop?
Derek do you have any performance figures for the 580, not familiar with this motor.
540's, 550's 600's yes not 580's

Bob
Logged
Officially a GOG.

Shipmate60

  • Global Moderator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,276
  • You bark - I will bite!!!
  • Location: Fareham
Re: One ESC - two motors.
« Reply #4 on: June 21, 2008, 10:21:13 PM »

Logged
Officially a GOG.

Bradley

  • Guest
Re: One ESC - two motors.
« Reply #5 on: June 21, 2008, 10:38:42 PM »

Thanks for the info Bob.  The motors are quoted as 580 but they are in a Chinese cheapy so, it is anyone's guess and they are powered by a 7.2v Ni-mh which I will replace with a 7.2v Ni-mh.  :-\
Derek.   :police:
Logged

Bradley

  • Guest
Re: One ESC - two motors.
« Reply #6 on: June 21, 2008, 10:41:54 PM »

Sorry, slight typographical error - should have read 7.2v Ni-cd being replaced with 7.2v Ni-mh.   :embarrassed:
Derek.   :police:
Logged

Shipmate60

  • Global Moderator
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 5,276
  • You bark - I will bite!!!
  • Location: Fareham
Re: One ESC - two motors.
« Reply #7 on: June 21, 2008, 10:46:53 PM »

I would go for a 20 amp ESC fused at 15 amps.
The real danger time is going from full ahead to dead astern, this can rack up the amps as the prop needs to fight against the foreward motion of the model.
If in doubt I am usually very gentle to get used to the handling characteristics. Then full ahead near the pondside where I am standing then chuck her full astern.
If she stops and runs astern all OK, if she dies she is at least close enough to recover.
If she blows fuse try a 20 amp and repeat.
If this blows you will have to get another ESC I am afraid, and run 1 ESC each motor.
Or get one of the cheapie Chinese ones, but they only give 50% power astern and if they blow only fit for bin.
My choice these days is ACTion as FLJ does a good recovery service.

Bob
Logged
Officially a GOG.

Bradley

  • Guest
Re: One ESC - two motors.
« Reply #8 on: June 21, 2008, 10:51:09 PM »

Many thanks, Bob.  You have told me just what I needed to know - very helpful.   O0 O0
Derek.   :police:
Logged
Pages: [1]   Go Up