Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: [1]   Go Down

Author Topic: precedent Perkasa 1:32 brushless setup  (Read 3227 times)

funfly3

  • Shipmate
  • *
  • Offline Offline
  • Posts: 3
precedent Perkasa 1:32 brushless setup
« on: August 08, 2012, 09:57:31 pm »
is it worth putting 3 small brush-less motors in the Perkasa or should i just stick with a 700bb or similar? and if I go the 3 motor option where do the 2 rudders go?


Kevin
Logged

Tug-Kenny RIP

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 7,625
  • Location: Newport. S Wales
Re: precedent Perkasa 1:32 brushless setup
« Reply #1 on: August 08, 2012, 10:03:34 pm »

I would cover the wash from the two outside propellers.   :}


ken
 
Logged
Despite the high cost of living   .......... It remains popular

funfly3

  • Shipmate
  • *
  • Offline Offline
  • Posts: 3
Re: precedent Perkasa 1:32 brushless setup
« Reply #2 on: August 08, 2012, 10:07:52 pm »
do they go slightly inboard? or inline with them?
Logged

Tug-Kenny RIP

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 7,625
  • Location: Newport. S Wales
Re: precedent Perkasa 1:32 brushless setup
« Reply #3 on: August 08, 2012, 10:37:52 pm »

In line would get the maximum prop wash.  There may be rotation of the centre prop to take into consideration however.  Perhaps the experts could help you here. 

My Fairmile D has four props but only two rudders  (not yet fitted) and I shall line these up with outside props.

cheers

ken
Logged
Despite the high cost of living   .......... It remains popular

John W E

  • I see no ships !!
  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 8,915
  • Location: South shields
Re: precedent Perkasa 1:32 brushless setup
« Reply #4 on: August 09, 2012, 12:10:42 am »
Logged
Knowledge begins with respect
But fools hate wisdom and discipline

triumphjon

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 789
  • Location: portsmouth , hampshire
Re: precedent Perkasa 1:32 brushless setup
« Reply #5 on: August 09, 2012, 08:13:48 am »
on all of my electric models i fit the rudder slightly off centre of the propshaft  , this allows me to withdraw thte shaft without disturbing the rudders  , you only need a couple of millimeters . a little for thought can save lots of down time if you need to service models later !jon
Logged

funfly3

  • Shipmate
  • *
  • Offline Offline
  • Posts: 3
Re: precedent Perkasa 1:32 brushless setup
« Reply #6 on: August 09, 2012, 06:02:25 pm »
oh no there are three rudders LOL not two
Logged

Tug-Kenny RIP

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 7,625
  • Location: Newport. S Wales
Re: precedent Perkasa 1:32 brushless setup
« Reply #7 on: August 09, 2012, 09:15:56 pm »

Now he tells us.                                   :kiss:


ken


Logged
Despite the high cost of living   .......... It remains popular

malcolmfrary

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 6,027
  • Location: Blackpool, Lancs, UK
Re: precedent Perkasa 1:32 brushless setup
« Reply #8 on: August 09, 2012, 09:32:50 pm »
Quote from: funfly3 on August 09, 2012, 06:02:25 pm
oh no there are three rudders LOL not two
Thats easy, then.  One each side and one in the middle.  Consider triumphjon's idea.
Logged
"With the right tool, you can break anything" - Garfield
Pages: [1]   Go Up
« previous next »
 

Page created in 0.366 seconds with 18 queries.