Model Boat Mayhem

Please login or register.

Login with username, password and session length.
Pages: 1 2 3 4 5 6 [7]   Go Down

Author Topic: 1/38 super-Guardian class patrol boat,3D printed kit build  (Read 16459 times)

Backerther

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,405
  • Model Boat Mayhem is Great!
  • Location: Japan
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #150 on: Today at 01:57:57 am »
It's a very fine day this day when the lake was calm enough to observe correctly how the boat would behave under actually  no wind/wave. She did a good sailing behaviour fundamentally as seen in the pics. The video will be here tomorrow to report this sailing scenes more and more precisely and vividly.!!!!!! :-)) :-)) :-)) :-)) :-))

This was the second day of trial run and there is still room for improvements like insufficient countermeasures against water ingress which defect was this time drastically reduced, but not perfect partly due to deck hatches being exposed to continuous powerful splash caused mainly by hi-speed run. O0 {-) :D   Next time of trial run will be mainly checked at this point. O0 O0 O0
HOWEVER, SHE SAILED UNCONCERNEDLY and VIVIDLY this time too as in the pics.!!!!!!! {-) {-) {-) {-) {-) :-)) :-)) :-))
All the waves are by her powerful effect. %% %%  Originally the surface was mirror-like in the beginning. ;D

So impressive with long and a bit symmetrical splash in the 2nd pic from the last.... O0 :-))
Logged

tica

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 506
  • Location: Vemmedrup, Denmark
    • Skalamodelskibe
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #151 on: Today at 07:38:37 am »
It looks great on the water  :-))

Logged
My postings are only reflecting my own opinion and should not be read as the holy grail of truth :-)

swiftdoc

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 334
  • Location: Germany
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #152 on: Today at 07:39:08 am »
Pic 8A would be my favourite, looking great! :-)) :-)) :-))  You were prepared perfectly for any eventually needed rescue O0
Logged

Backerther

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,405
  • Model Boat Mayhem is Great!
  • Location: Japan
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #153 on: Today at 08:18:44 am »
tica,
Thank you so much for your good impression about the sailing scenes of my fast patrol boat still under trial run.


Arno,
I also do like to see a boat turning sharply and its wake left clearly behind the boat. :-)) :-)) :-))
The scenes of a boat/ship to turn are normally so dynamic by the waves around the bow through mid-ship followed by the wakes behind the stern which are also powerful to see dependent upon the speed. :-)) :-))   Wow wow!! %% %%


Kiyo
Logged

KitS

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 777
  • Getting back into the hobby after years adrift...
  • Location: Lydney, Glos. UK
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #154 on: Today at 12:36:58 pm »
She looks REALLY good in action.  :-))


And you're right about a 'mirror-like' surface on the lake!   :}
Logged
Regards
Kit

Backerther

  • Full Mayhemer
  • *****
  • Offline Offline
  • Posts: 1,405
  • Model Boat Mayhem is Great!
  • Location: Japan
Re: 1/38 super-Guardian class patrol boat,3D printed kit build
« Reply #155 on: Today at 01:30:28 pm »
KitS,
Thank you for your kind comment.! %%
........This day, the surface looks pretty well like a mirror when seen from the distant place as in the pic below.....
But actual surface was REALLY dirty as seen in another pic below....partly because of no water flow, not shaky on the lake like a mirror ..See pic3!! {:-{ %% :-X :o    This condition is nothing but a mirror, a water mirror.!!! :D {-) O0 :-))
Kiyo
Logged
Pages: 1 2 3 4 5 6 [7]   Go Up
« previous next »
 

Page created in 0.021 seconds with 19 queries.